Search tips
Showing 29 results View by: Thread Post Sort by
    Answered

  • RE: OPA4322: short-circuit current of OPA4322

    Former Member
    Former Member
    Resolved
    Hello Minkyung, Kai is correct. To add a little more detail to his answer, the short-circuit current specification is essentially a maximum current output specification for the op amp. However, it is only true for the conditions given in the datasheet…
    • Answered

  • OPA4322: TINA simulation as a DAC buffer (Unity gain buffer )

    Resolved
    Part Number: OPA4322 Other Parts Discussed in Thread: TINA-TI Hi OPAMP folks, I'm doing TINA simulation with OPA4322 as an unity gain buffer. Could you help advise for its operation? What I'm trying to do : I want to implement an unity gain…
    • Resolved
    • Answered

  • OPA4322: Output saturation on TINA-TI

    Resolved
    Part Number: OPA4322 Other Parts Discussed in Thread: TINA-TI , OPA4376 Hi, Our customer is considering adder circuit with OPA4322 and simulated with TINA-TI but saturation was seen saturation as following. Their requirement is - Add offset…
    • Resolved

  • OPA4322-Q1: OP-AMP Behavior Under Off Condition

    TI Thinks Resolved
    Part Number: OPA4322-Q1 Other Parts Discussed in Thread: OPA2348-Q1 , Hello TI Team, I am using both of the above op amps (OPA4322-Q1 and OPA2348-Q1). When these op-amps are off ( It is possible that (+) input voltage can go up to 16V through a 49…

  • OPA4322 TINA model clamping at 100mV

    Other Parts Discussed in Thread: OPA4322 Hi guys, I've simulated with OPA4322 negative feedback amplifier. Simulation is observed clamping at 100 mV, while in reality measurement such clamping does not occur.(minimum is GND) does anybody occur this…

  • Could you help to recommend one amplifier which is pin to pin with OPA4322?

    Other Parts Discussed in Thread: OPA4322 Hi Dears, Could you help to recommend one amplifier which is pin to pin with OPA4322AIPWR TSSOP package, 1) with similar performance, the bandwidth>5MHz is OK; 2) fit for Vcc=2.7-5.5V application; 3) The Vol…
    • Answered

  • OPA2322,OPA4322 : channel variation

    Resolved
    Other Parts Discussed in Thread: OPA2322 , OPA4322 Hi I will use OPA2322 or OPA4322. How can I estimate channel variation? Regards
    • Resolved

  • OPA2322: Current Sensing signal conditioning

    TI Thinks Resolved
    Part Number: OPA2322 Other Parts Discussed in Thread: OPA4322 , OPA4323 , TLV9064 Customer would like to use OPA4322AIPWR for the 2nd source of the TLV9064IPWR. here list is comparison table. The OPA is being used for the signal conditioning for phase…

  • TSV994AIDT P-P replacement

    TI Thinks Resolved
    Other Parts Discussed in Thread: TLV9054 , TLV9064 , OPA4322 Hi sir, Could you pls kinldy suggest if there is P-P solution to replace ST TSV994AIDT ? Thanks a lot! (Wide BW 20MHz, R-R, 5V, CMOS OPA, small offset, quad) Thanks a lot!
    • Answered

  • RE: LMH6502: LMH6502 (R-PDSO-G14 package) footprint/land pattern

    Resolved
    Hi Jason and welcome to E2E, There is a pad layout description on page 45 of the OPA4322 datasheet found here www.ti.com/.../opa4322.pdf . You may have to make your own pad for this one. Best regards, Sean

Didn't find what you are looking for? Post a new question.