Search tips
Showing 4,963 results View by: Thread Post Sort by

  • PRU-ICSS-INDUSTRIAL-SW: Purpose of IEP counter

    Part Number: PRU-ICSS-INDUSTRIAL-SW Hi, I am developing an Ethernet driver for PRU-ICSSG (SR 2.0) using dual mac firmware for AM6548 chip based on a proprietary RTOS. I am using the SDK 7.01 based DUAL EMAC firmware from the below source: …
    • Answered

  • PRU-ICSS-INDUSTRIAL-SW: PRU-ICSS-ETHERCAT-SLAVE support for AM65x SR2.0

    Resolved
    Part Number: PRU-ICSS-INDUSTRIAL-SW Dear TI team, there has been a new release of the EtherCAT slave software, but the release notes don't say whether this release supports both SR 1.0 and SR 2.0 AM65x, or just one. I saw in the newly released SDK…
    • Resolved
    • Answered

  • PRU-ICSS-INDUSTRIAL-SW: Link status handling by interrupt

    Resolved
    Part Number: PRU-ICSS-INDUSTRIAL-SW Hi, I am developing an Ethernet driver for PRU-ICSSG (SR 2.0) using dual mac firmware for AM6548 chip based on a proprietary RTOS. I am using the DUAL EMAC firmware based on SDK 7.01. I have checked the test program…
    • Resolved
    • Answered

  • PRU-ICSS-INDUSTRIAL-SW: Jumbo frame support by PRU-ICSSG

    Resolved
    Part Number: PRU-ICSS-INDUSTRIAL-SW Other Parts Discussed in Thread: AM6548 Hi, I am developing an Ethernet driver for PRU-ICSSG, for AM6548 chip, based on ICSS-G Dual EMAC Firmware. I want to support Jumbo Frames if possible. Is there an place…
    • Resolved

  • PRU-ICSS-INDUSTRIAL-SW: Latch signals for AM65xx EtherCAT Slave

    Part Number: PRU-ICSS-INDUSTRIAL-SW Other Parts Discussed in Thread: AM3359 Hi TI, I am currently configuring AM65xx Board as an EtherCAT Slave. I built ethercat_slave_full application and did the proposed changes to configure the MII interface. Everything…

  • PRU-ICSS-INDUSTRIAL-SW: The function hcc_init is missing after upgrading HCC-SNMP-Stack to a licenced version

    Part Number: PRU-ICSS-INDUSTRIAL-SW Hello, we use the Profinet from PRU-ICSS-Profinet_Slave_01.00.03.04 on AM335x- For production we licenced the SNMP-Strack from HCC and follow your instructions to embedd it to the Profinet-Stack. And here comes…

  • PRU-ICSS-INDUSTRIAL-SW: Checksum offload support in ICSS-G DUAL EMAC firmware

    TI Thinks Resolved
    Part Number: PRU-ICSS-INDUSTRIAL-SW Hi, As discussed in the thread https://e2e.ti.com/support/processors/f/791/p/906923/3365944#3365944 , currently checksum offload is not supported by dual emac firmare, but it was mentioned,"We do have updated firmware…

  • AM2612-Q1: Is PRU-ICSS support MCASP?

    Part Number: AM2612-Q1 Hi team, In our one-page, it shows PRU-ICSS support I2S, is it support MCASP? BRs Shuqing
    • Answered

  • MCU-PLUS-SDK-AM243X: Device without Industrial Ethernet protocol using ICSS-EMAC, PRU-ICSS driver

    Resolved
    Part Number: MCU-PLUS-SDK-AM243X Hello We are planning to have the possibility to run our device also without Industrial Ethernet protocol, so both Ethernet ports should run as "normal" IP ports (LWIP stack). For this I still want to use the ICSS…
    • Resolved
    • Answered

  • PRU-ICSS-INDUSTRIAL-SW: Profinet on Linux

    Resolved
    Part Number: PRU-ICSS-INDUSTRIAL-SW Dear team, our customer is interested in using our Sitara processor and was curious if we support Profinet on the Linux SDK. Referring to the other thread from 2017, you commented that it was feasible. What is…
    • Resolved

Didn't find what you are looking for? Post a new question.