TI E2E support forums
Menu
Search through millions of questions and answers
User
Menu
Search through millions of questions and answers
User
E2E™ support forums
Forums
Amplifiers
Audio
Clock & timing
Data converters
DLP® products
Interface
Isolation
Logic
Microcontrollers
Motor drivers
Power management
Processors
RF & microwave
Sensors
Site support
Switches & multiplexers
Tools
Wireless connectivity
Archived forums
Archived groups
Technical articles
Analog
Automotive
DLP® technology
Embedded processing
Industrial
Power management
0
TI training
Tech days
Online training
Live events
Power Supply Design Seminar
Getting started
More
Cancel
简体中文
Search tips
Showing 43 results
View by: Thread
Post
Sort by
Relevance
Oldest to Newest
Newest to Oldest
Dennis McGlumphy
over 1 year ago
Power management
Power management forum
RE: REF102: Op-Amp selection for constant current source
Dear Mr. Kuehl Thank you again. This resolves my questions.
CLAVERIE Alain
over 2 years ago
Power management
Power management forum
REF102: REF102
Resolved
Part Number:
REF102
Hi I need to design a current source of about 30 micro amps (UA) it should
user6225510
over 1 year ago
Power management
Power management forum
REF102: REF102 + OPA227 Precision Current Source Issue
Resolved
Part Number:
REF102
Dear member of this forum, I need to generate a very precise 10 uA current . I
user5828747
over 2 years ago
Power management
Power management forum
REF102: Output voltage noise density v.s. frequency
TI Thinks Resolved
Part Number:
REF102
Hello, I am currently looking for a low noise, low drift (<5ppm/C) voltage reference which output voltage is around 10V. And I care not only the low frequency noise but also the broad band noise (up to 10KHz). I only find the...
Raymond Zhang1
6 months ago
Amplifiers
Amplifiers forum
RE: INA326: INA326 REF 200
Hi Mannan, Enclosed are links about how to build V to I converter. https://www.ti.com/lit/an/sbva001/sbva001.pdf https://www.ti.com/lit/ug/slau507/slau507.pdf The
REF102
and REF200 are legacy devices, and I am not sure that they will work well...
F_F_S
over 2 years ago
Power management
Power management forum
REF102: REF102 stacked : what is the maximum error?
TI Thinks Resolved
Part Number:
REF102
Hi, on datasheet of
REF102
(figure 11) is write that is possible to put more
REF102
on stacked to obtain multiple voltage. If I use 2 of
REF102
, what is the maxium error on 20V ? Thanks?
Marcoo Z
over 1 year ago
Power management
Power management forum
RE: REF3430: Why does RFE3430's Output Current support -10 mA?
Hi Eggsy, The purpose of sinking current is if the output of the reference is a higher voltage than expected. Keep in mind that voltage references are very versatile and not just always connected to an ADC or DAC. Sometimes they can be use as pull-up...
Poh Kok Keng
over 3 years ago
Power management
Power management forum
REF102: Solderability test report for MPN: REF102BP
TI Thinks Resolved
Part Number:
REF102
hi, Can I check if I can get the solderability test report for
REF102
BP device? End customer want to know if this part following one of the both standard CEI-68-2-54 or JESD-22-B102. best regards, kpk
Rajesh Matere
over 3 years ago
Amplifiers
Amplifiers forum
RE: Load Independent 5mA constant current source (Load Resistance 650 ohm to 750 ohm).
Hi Leonard, Thanks for the updated link. Here I have attached my current design and application design overview. Yes, we need programmable amplifier with Ratio-metric or Analog output and 5mA constant current for bridge excitation (resitance may...
Marcoo Z
over 3 years ago
Power management
Power management forum
RE: REF102: Datasheet question: Thermal hysteresis missing
Hi Sven, If it is not in the datasheet then we do not have a value for it. For thermal hysteresis if you follow SNVA602, the document you mentioned, you can try to measure it. Keep in mind that the first initial cycle of thermal hysteresis will be...
<
>
Didn't find what you are looking for? Post a new question.
Ask a new question