Search tips
Showing 15,129 results View by: Thread Post Sort by

  • SN65HVDA542-Q1: Internal BUS Termination

    TI Thinks Resolved
    Part Number: SN65HVDA542-Q1 Tool/software: Dear CAN Transceiver Support Team. One of our customers is looking for an internal bus termination resistor for a CAN transceiver. It is also desirable to be able to enable/disable the bus termination resistors…

  • LDC5071-Q1: LDC5071-Q1 / LDC5072-Q1 for 100 µrad, 5 kHz Inductive Torque Sensing

    TI Thinks Resolved
    Part Number: LDC5071-Q1 Other Parts Discussed in Thread: LDC5072-Q1 , , TIDA-010961 , LDC1101 Hello, We are evaluating the LDC5071-Q1 and LDC5072-Q1 for a non-contact robotic joint torque sensor using a custom rotary inductive coil/target. Our requirements…

  • TPS7B82-Q1: TPS7B8233-Q1: 5 V to 3.3 V, about 150 mA - capacitor check

    TI Thinks Resolved
    Part Number: TPS7B82-Q1 Hi, A quick check on a TPS7B8233-Q1 (fixed 3.3 V) running from a 5 V buck output: - IN and EN tied together to the 5 V rail. The rail has 2 x 47 uF 16 V X7R + 1 uF close by (the buck's output capacitors). - OUT: 2.2 uF X7R at…

  • UCC27624-Q1: Technical Support Request — Output Voltage Drop at Switching Frequencies Above 5 kHz (UCC27624-Q1)

    TI Thinks Resolved
    Part Number: UCC27624-Q1 Dear Texas Instruments Support Team, I am writing to request technical assistance regarding an application issue with the UCC27624-Q1 (30 V, 5 A, Dual-Channel, Low-Side Gate Driver with –10 V Input Capability, for Automotive…
    • Answered

  • TPS4HC120-Q1: TPS4HC120-Q1: Discrepancy between Table 5-1 and Table 7-2 regarding SEL0/SEL1

    Resolved
    Part Number: TPS4HC120-Q1 Hello, I am reviewing the Rev. B datasheet for the TPS4HC120-Q1 and found a documentation discrepancy regarding the current-sense multiplexer pins. Table 5-1 (Pin Functions) clearly defines SEL0 as the "channel-selection…
    • Resolved

  • TPS4HC120-Q1: Clarification on TPS4HC120-Q1 Operation at 5 V VBB and Current Limit Threshold

    TI Thinks Resolved
    Part Number: TPS4HC120-Q1 Hello TI Team, I have a few questions regarding the TPS4HC120-Q1. Operation with VBB = 5 V According to the datasheet, the nominal operating voltage range for the VBB pin is 4 V to 18 V. However, many of the electrical…

  • TDA4VH-Q1: TDA4VH -G vs. -5

    Part Number: TDA4VH-Q1 Could you confirm if there are any internal hardware differences between the General purpose part (TDA4VH88TGAALYRQ1) and High security, R5F lockstep capable part (TDA4VH88T5AALYRQ1), or are these using the same silicon?

  • TPS1HTC30-Q1: TPS1HTC30-Q1: EN pin - Table 5-1 states internal pullup, but Electrical Characteristics specifies internal pulldown (SLVSGL4A)

    TI Thinks Resolved
    Part Number: TPS1HTC30-Q1 Hi, I am using the TPS1HTC30AQPWPRQ1 and found a contradiction in the datasheet (SLVSGL4A, revised May 2026) regarding the EN pin. (a) Table 5-1. Pin Functions, EN pin: "Enables/disables channel output current, internal pullup…

  • TPS546D24A: Power Solution & Sequencing Review for Agilex 5 SoC (TPS546D24A, TPS543C20, LMQ644A2-Q1)

    TI Thinks Resolved
    Part Number: TPS546D24A Other Parts Discussed in Thread: TPS543C20 , LMQ644A2-Q1 , LM3880 , TPS386000 , TPSM5D1806 Hello TI Team, I am designing a power supply and sequencing solution for an Intel/Altera Agilex 5 SoC and would like to verify the suitability…

  • TCAN1042-Q1: Pull up the Pin 5

    TI Thinks Resolved
    Part Number: TCAN1042-Q1 Hello team, My customer mistakenly pull up the pin 5 in the Gerber, which should be NC, is there any influence? Is it necessary to change it? BR, Daniel

Didn't find what you are looking for? Post a new question.