• RE: SN74LVC1G17-Q1: Use between Switching States

  

  Clemens Ladisch

  device number of channels SN74LVC1G17-Q1 1 SN74LVC2G17-Q1 2 SN74HCS125-Q1 4 SN74AC17-Q1 6 SN74HCS541-Q1 SN74LVC9541A-Q1 8 LVC/AC have higher drive strength than HCS, but the difference probably does not…

  • 1 month ago
  • Logic
  • Logic forum
Answered

• SN74LVC1G17: Trouble with positive input tolerances

  

  Marco Veschini

  Resolved

  Part Number: SN74LVC1G17 Other Parts Discussed in Thread: TLV1851 , SN74HCS125 Tool/software: I've used this logic buffer (schmitt trigger) to receive a discrete signal which voltage can go from +15V to 0V. A 12Kohm resistor connected to +15V provides…

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum

• SN74LVC125A: input rise/fall time for xOE_ pins

  

  Kazuhiko Hirano

  TI Thinks Resolved

  Part Number: SN74LVC125A Other Parts Discussed in Thread: SN74HCS125 Hello Q1: My customer uses SN74LVC125A. Datasheet says input transition rise or fall rate is less than 8ns/V as follows. Is this spec applies to not only 1A to 4A but also 1OE_ to 4OE_…

  • over 2 years ago
  • Logic
  • Logic forum

• RE: SN74LVC3G17: Does TI has Pin-to-pin Q-grade or good Q-grade solution for SN74LVC3G17DCUR

  

  Clemens Ladisch

  The most similar -Q1 device would be the SN74HCS125-Q1.

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• TXU0304: Suggestions on use for SPI over ~0.8m distance

  

  Neet

  Resolved

  Part Number: TXU0304 Other Parts Discussed in Thread: SN74HCS125 , SN74LVC2G86 , LM311 , SN74HC86 , SN74LV86A , SN74HCS86 , LM393LV , LM339LV , TMP144 Hello, We are trying to evaluate a low cost option for data transmission from single remote sensor…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• SN74HC125: Product information for heat-resistant specifications of general purpose ICs and heat-resistant measures

  

  user4427847

  Answer Suggested

  Part Number: SN74HC125 Other Parts Discussed in Thread: SN74HCS125 , SN74HCS541 , SN74HCS138 お世話になります 弊社製品の温度特性検査にて御社のICを使ってます 汎用 (general purpose) IC 74HC125、74HC138、74HC541 温度範囲はマイナス４０度からプラス９０度です (temp range is -40 to +90 C) 数年でICの交換が必要となる為…

  • over 2 years ago
  • Logic
  • Logic forum

• RE: SN74HCS244-Q1: buffer IC layout placement

  

  Clemens Ladisch

  You can use two four-channel buffers, e.g., SN74HCS125-Q1.

  • over 1 year ago
  • Logic
  • Logic forum

• LMK04828: High frequency noise on SPI signals

  

  RajK

  TI Thinks Resolved

  Part Number: LMK04828 Other Parts Discussed in Thread: SN74HCS125 Hello, Could you please suggest techniques to mitigate high frequency noise on SPI lines. The details are below - SPI frequency - 20MHz Noise frequency ~1GHz @ -30dBc Can we add…

  • over 5 years ago
  • Clock & timing
  • Clock & timing forum

• SN74AVCH16T245: IO with bus hold random status at power up

  

  Silvia Ferreira1

  TI Thinks Resolved

  Part Number: SN74AVCH16T245 Other Parts Discussed in Thread: SN74HCS125 , TLV840 , TLV809E During the device power-up we’ve notice the IO-with bus hold-status is random, when the IO is at high impedance. We would like to know if, setting the IO at the…

  • over 3 years ago
  • Logic
  • Logic forum
Answered

• RE: SN74HC14: Non-Inverting Schmitt-Trigger with clamp-diodes

  

  Ue

  Resolved

  Clemens Thank you for the quick reply. As Schmitt-Trigger inputs are required it would then be the the SN74HCS125 Best regards Ueli

  • over 5 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.