Search tips
Showing 107 results View by: Thread Post Sort by

  • TMUX1208-Q1: IBIS file is Not inclu

    TI Thinks Resolved
    Part Number: TMUX1208-Q1 Other Parts Discussed in Thread: TMUX1208 , TMUX1108 Hi I try to download the IBIS file of TMUX1208 to run the simulation, but it is not workable because the S1~S8 are "nc" after compare with TMUX1108. thanks

  • TMUX1208: TMUX1208 with 4-20mA loop signals

    TI Thinks Resolved
    Part Number: TMUX1208 Other Parts Discussed in Thread: RCV420 , TMUX7208 , INA180 , TLV9001 Tool/software: Dear TI Support, I need to interface Sensors in an industrial gloove box, O2 Sensor with passive with 2 wires 4-20mA output and H2O Sensor active…
    • Answered

  • TMUX1208: Alternative part for TMUX1108

    Resolved
    Part Number: TMUX1208 Other Parts Discussed in Thread: TMUX1108 Hi Ti team, I want to use TMUX1208 for replacement TMUX1108/ Can we connect Pin1 NC (TMUX1208) to GND? (Pin1 is GND for TMUX1108) Beside that, there are any potential issue if I just replace…
    • Resolved

  • TMUX1208: S/O: 458129

    TI Thinks Resolved
    Part Number: TMUX1208 Hello, I have a customer who ordered P/N: TMUX1208PWR They claim this part is Oxidized, can you please confirm from the picture if this is the case, or if this part is still in good condition? Thanks!

  • TMUX1208: Source or Drain negative transient voltage

    TI Thinks Resolved
    Part Number: TMUX1208 Hi expert, My customer found Drian negative voltage is over min on Abs rating, about -750mV, duration 20ns. We did not specify transient spec for VS or VD. Here is the waveform, CH1 is GND to GND voltage, CH2 is pin8 to GND…
    • Answered

  • TMUX1208: Internal Clamp Diode on S and B Pins to VDD/VCC (TMUX1208 and SN74LVC1G3157)

    Resolved
    Part Number: TMUX1208 Other Parts Discussed in Thread: SN74LVC1G3157 Tool/software: It's implied by the data sheets that there is a clamp diode between the Sx and VDD pins of TMUX1208, and similarly Bx and VCC pins of SN74LVC1G3157 (the SN74LVC1G3157…
    • Resolved

  • TMUX1208: Questions regarding D pin & adding bypass cap

    TI Thinks Resolved
    Part Number: TMUX1208 Other Parts Discussed in Thread: LDC1314 Hello experts, Currently my customer is reviewing our TMUX1208 for their induction project. They are having a few failure cases with their design, where the D pin became short. IC & VDD…

  • TMUX1208-Q1: Powered-off protection for S1-S8 inputs.

    TI Thinks Resolved
    Part Number: TMUX1208-Q1 Hello, Does the TMUX1208QRSVRQ1 chip have powered off protection for the source inputs? I would like to know if there is a requirement to have 5V brought up on the bus before applying analog inputs to S1-S8. Thank you
    • Answered

  • TMUX1208-Q1: Suggested termination for unused pin

    Resolved
    Part Number: TMUX1208-Q1 Hello Expert, Could we leave floating at unused Sx pins? Or should we pull-up/down at unused pin from any reason(e.g. cross talk, noise coupling, ESD, etc)? Best regards, Kazuki Kuramochi
    • Resolved

  • TMUX1208: TMUX1208PWR MUX Pspice File

    TI Thinks Resolved
    Part Number: TMUX1208 Tool/software: Can I receive the pspice file for the TMUX1208PWR MUX? thank you

Didn't find what you are looking for? Post a new question.