TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Enterprise Automation Integration
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
    • Analog
    • Automotive
    • DLP® technology
    • Embedded processing
    • Industrial
    • Power management
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 47 results View by: Thread Post Sort by
  • TPS546A24A: Internal pull-up at EN/UVLO pin

    teritama
    teritama
    Other Parts Discussed in Thread: TPS546A24A , TPS62913 Part Number: TPS546A24A Hi team, In datasheet EN/UVLO pin has internal pull-up(Ihys) like below figure. We try to use this pull-up as pull-up of Power good pin on TPS62913. But, TPS546A24A doesn't…
    • over 1 year ago
    • Power management
    • Power management forum
  • TPS546A24A: Start-up instability

    Yann Nocerino
    Yann Nocerino
    TI Thinks Resolved
    Part Number: TPS546A24A Hello E2E community, I have done two power supply designs using TPS546A24A with pin strapping only. The PCB have been built and assembled and I'm experiencing some trouble on start-up due to instability. -Input 10V, freq 550kHz…
    • over 1 year ago
    • Power management
    • Power management forum
  • TPS546A24A: Vboot and Vout_command behavior confirme

    Ben Kuo
    Ben Kuo
    TI Thinks Resolved
    Part Number: TPS546A24A Dear team, Customer would like to set Vboot as 0.8V(floating VSEL pin) and change output voltage by Vout_command by PMBUS after system power on. They want to double check Vout_command value will not be import in EEPROM and Vboot…
    • over 1 year ago
    • Power management
    • Power management forum
  • TPS546A24A: schematic check

    GARETH OU
    GARETH OU
    TI Thinks Resolved
    Part Number: TPS546A24A Hi Input voltage 6.5-13.2V to 5V / at 10A, 3.3V / at 9A PWM Is TPS546A24A suitable? Thanks
    • over 1 year ago
    • Power management
    • Power management forum
  • TPS546A24A: IOUT_UC_FAULT Issue

    Phillip Lam1
    Phillip Lam1
    TI Thinks Resolved
    Part Number: TPS546A24A I have a lot of bulk cap on this rail and the operation is set to "ON". This issue happens when we use the PMBUS operation command to turn on the VR. We don't use the EN pin, or in other words the ON/OFF register is set to 0x1B…
    • over 1 year ago
    • Power management
    • Power management forum
  • Answered
  • TPS546A24A: Power Down Voltage too Slow

    Phillip Lam1
    Phillip Lam1
    Resolved
    Part Number: TPS546A24A Other Parts Discussed in Thread: TPS546D24A I have about 800uF of output capacitance. VOUT is 1.2V My VR is configure to power on/off based on the operation register. When I power down it takes about a minute or so to go below 100mV…
    • Resolved
    • over 1 year ago
    • Power management
    • Power management forum
  • Answered
  • TPS546A24A: Low Output Bulk Capacitance Causing Start Up Issue

    Phillip Lam1
    Phillip Lam1
    Resolved
    Part Number: TPS546A24A I have 4x TPS546A24A configured as single phase rail for each regulator. At the moment, there is no load device. I am pre-testing (developing FW) on the board before populating my intended load device. All but one regulator is…
    • Resolved
    • over 2 years ago
    • Power management
    • Power management forum
  • Answered
  • TPS546A24A: TPS546A/B/D24A possible output voltage

    Hans
    Hans
    Resolved
    Part Number: TPS546A24A Hello Team, there is some confusion regarding the possible Vout for TPS546A/B/D24A. All their datasheets specify on page 1: and on page 12: Question: Is it possible to set Vout to 6V? Thanks and Best Regards, Hans
    • Resolved
    • over 2 years ago
    • Power management
    • Power management forum
  • TPS546A24A: supports 0.1V low dropout operation?

    Jerry Chen82343
    Jerry Chen82343
    TI Thinks Resolved
    Part Number: TPS546A24A Hi team, I'm looking for solution with 0.4Vout to 3Vout/2A adjustable output from 3.1Vin. Does TPS546A24A support 3.1Vin to 3Vout? Thanks.
    • over 2 years ago
    • Power management
    • Power management forum
  • Answered
  • TPS546A24A: EVM question

    Shinya Sawamoto
    Shinya Sawamoto
    Resolved
    Part Number: TPS546A24A Other Parts Discussed in Thread: TPS546B24A Hello team, I'd like to order an TPS546A24A EVM for my client. On the TI.com, it connects to TPS546 B 24A_EVM instead of TPS546A24A. Would it work similar to see the performance for TPS546A24A…
    • Resolved
    • over 2 years ago
    • Power management
    • Power management forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question
About TI
Company News & events Investor relations Corporate citizenship Careers Contact us
Quick links
TI E2E™ design support forums Customer support center Packaging Quality & reliability TI university program myTI FAQ
Buying
Ordering resources Ordering help & FAQs BOM & cross reference tool Quick add to cart Authorized distributors
Connect with us

Texas Instruments has been making progress possible for decades. We are a global semiconductor company that designs, manufactures, tests and sells analog and embedded processing chips. Our products help our customers efficiently manage power, accurately sense and transmit data and provide the core control or processing in their designs.

Cookie policy Privacy policy Terms of sale Terms of use Trademarks Website feedback

© Copyright 1995-2023 Texas Instruments Incorporated. All rights reserved.