Search tips
Showing 16 results View by: Thread Post Sort by

  • TPS62811-Q1: Pre-biased start up

    TI Thinks Resolved
    Part Number: TPS62811-Q1 Hi team, I would like to enable TPS62811-Q1 (Vout = 1.15V setting) into pre-biased (1.1V) load. It looks this device has active discharge feature, but I am not sure if it (50ohm pull down) is active all the time during device...

  • TPS62811-Q1: ILIMNEG Parameter

    • Resolved
    Part Number: TPS62811 - Q1 Hi Team, May we ask for more information about the ILIMNEG parameter

  • TPS62811-Q1: TPS62811-Q1 Pin FMEA

    TI Thinks Resolved
    Part Number: TPS62811-Q1 TPS62811-Q1 Pin FMEA

  • TPS62811-Q1: Output Impedance Plot Across Freq to Bandwidth of Regulator

    TI Thinks Resolved
    Part Number: TPS62811-Q1 Do you have an output impedance plot across frequencies up to the bandwidth of the regulator? For our design, we are operating at 2.2MHz.

  • TPS62811-Q1: Schematic review request

    • Resolved
    Part Number: TPS62811 - Q1 Hello Team, My customer asked us to review their application schematic

  • TPS62811-Q1: bode plot for 3 compensation pattern

    • Resolved
    Part Number: TPS62811 - Q1 Hi team, Could you share the bode plot to see phase margin and gain margin

  • TPS62811-Q1: Higher inductance than recommended

    TI Thinks Resolved
    Part Number: TPS62811-Q1 Hi team, Vin=5V, Vout=1.8V, Iout=0.5 to 1A Fsw=2.1MHz If I calculate inductance based on 30% inductor ripple current, the inductance should be around 1.8uH. So I would like to use 1.8uH to 2.2uH coil for LC filter with matched...

  • TPS62811-Q1: 0.6V output configuration

    • Resolved
    Part Number: TPS62811 - Q1 How do you recommend to achieve 0.6V out? The datasheet doesn’t give

  • TPS62811-Q1: Are we going to have noneQ version

    • Resolved
    Part Number: TPS62811 - Q1 Hi Sir, My customer is asking if we have NoneQ version TPS62811

  • TPS62811-Q1: RC snubber from SW node to GND is needed or not

    • Resolved
    Part Number: TPS62811 - Q1 Hi team, May I know if TPS62811 - Q1 need to add RC snubber from SW pin

Didn't find what you are looking for? Post a new question.


All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI worldwide | Contact us | myTI login | Corporate citizenship

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2020 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy policy | Terms of use