Search tips
Showing 20 results View by: Thread Post Sort by

  • CCS/UCD3138A64OEVM-662: interfacing wifi via uart

    TI Thinks Resolved
    Part Number: UCD3138A64OEVM-662 Tool/software: Code Composer Studio void init_uart0(void) { volatile unsigned char rx_byte; Uart0Regs.UARTCTRL3.bit.SW_RESET = 0; //software reset while initializing UART Uart0Regs.UARTCTRL0.bit.DATA_SIZE = 7; //8 bits…

  • CCS/UCD3138A64OEVM-662: burning or loading program permanently into flash memory

    TI Thinks Resolved
    Part Number: UCD3138A64OEVM-662 Tool/software: Code Composer Studio Sir I need to burn my program into flash memory and it should remain over there permanently Now when I'm running a blinking LED program, led blinks until my board is connected to power…

  • UCD3138A64OEVM-662: No ROM detected

    Part Number: UCD3138A64OEVM-662 Other Parts Discussed in Thread: UCD3138A64 Hello everyone , I have bay the UCD3138A64 EVM622 on TI store, When I use GUI "Scan Device in ROM... " , He can not find the ROM When I use GUI "VICE... " , He can not find…

  • CCS/UCD3138A64OEVM-662: UCD138A64 and code composer studio validation id doubt.

    TI Thinks Resolved
    Part Number: UCD3138A64OEVM-662 Other Parts Discussed in Thread: UCD3138A64 , UCD3138 , UNIFLASH Tool/software: Code Composer Studio We are using UCD3138A64 along with the XDS100V2 debug probe. As suggested in the earlier thread, When we load the…

  • CCS/UCD3138A64OEVM-662: Program does not run when I disconnect the target power source and reconnect it.

    TI Thinks Resolved
    Part Number: UCD3138A64OEVM-662 Other Parts Discussed in Thread: UCD3138A64 Tool/software: Code Composer Studio I have UCD3138A64 module with me, every time before i burn the code using CCS I clear the flash memory and than load the desired code, during…
    • Answered

  • UCD3138128: How to erase/program using JTAG

    Resolved
    Part Number: UCD3138128 Other Parts Discussed in Thread: SEGGER , CCSTUDIO , , UCD3138A64 Tool/software: I seem to have locked up my application due to an error in the checksum clearing routine. I was hoping to be able to clear the memory with JTAG…
    • Resolved
    • Answered

  • UCD3138128A: SPI BUS used as GPIO

    Resolved
    Part Number: UCD3138128A Other Parts Discussed in Thread: UCD3138128 , , UCD3138A64 , UCD3138A64OEVM-662 Tool/software: We are having trouble enabling the SPI signal TDO and TDI as GPIO outputs. Is there other discussions about this I could examine…
    • Resolved

  • UCD3138064A: PMBus/I2C Master Mode Example

    TI Thinks Resolved
    Part Number: UCD3138064A Other Parts Discussed in Thread: UCD3138A64OEVM-662 , Hello, I am looking for some example code for the UCD31xx that would allow me to talk to an EEPROM. The technical reference manual shows all of the registers needed for I2C…

  • No ROM detected

    TI Thinks Resolved
    Part Number: UCD3138A64OEVM-662 Good Morning I have the same card , when I put the USB , it's okay the LED is on , But when I use Device GUI it say that no rom detected unable to communicate with rom , device may be in flash mode . Please help me…
    • Answered

  • UCD3138A64: Firmware cannot be downloaded

    Resolved
    Part Number: UCD3138A64 Hi, I met a problem when testing UCD3138A64OEVM-662: the firmware "Lab_2_UCD3138A64.x0" cannot be downloaded into the EVM. After I launched "UCD3XXX Device GUI" and click on "Scan device in ROM mode", it seems the GUI has identified…
    • Resolved

Didn't find what you are looking for? Post a new question.