• RE: UCD90160: UCD90160 Configuration File Write Error

  

  yihe

  Hello We haven't heard from you for a while and assumed that the issue has been solved. Please reply if any further help is needed. Regards Yihe

  • 3 months ago
  • Power management
  • Power management forum
Answered

• RE: UCD90160: can not find ucd90160

  

  yihe

  Resolved

  Hello We haven't heard from you for a while and assumed that the issue has been solved. Please reply if any further help is needed. Regards Yihe

  • 4 months ago
  • Power management
  • Power management forum
Answered

• RE: UCD90160: UCD90160

  

  yihe

  Resolved

  Hello We haven't heard from you for a while and assumed that the issue has been solved. Please reply if any further help is needed. Regards Yihe

  • 4 months ago
  • Power management
  • Power management forum
Answered

• UCD90160: Does Fusion Digital Power Manufacturing Tool supports command line

  

  Danilo Austria

  Resolved

  Part Number: UCD90160 Hi Team, The customer's R&D team use Fusion Digital Power Designer to program the UCD90160. The customer would like to use Fusion Digital Power Manufacturing Tool and would like to confirm if it supports command line to use…

  • Resolved

  • 24 days ago
  • Power management
  • Power management forum
Answered

• UCD90160: MON14~16 cannot detect low voltage.

  

  Yoonsun Kim

  Resolved

  Part Number: UCD90160 Hello, I need to measure 32 voltages so use two ucd90160. The voltage range I should check is 0.1 ~ 1.5V. When open state on MON# input, measured values of MON14 ~ 16 always are over about 0.19V. When I applied 0.1V to MON# ports…

  • Resolved

  • 8 months ago
  • Power management
  • Power management forum
Answered

• WEBENCH® Tools/UCD90160: UCD90160N Designer tool

  

  user6336185

  Resolved

  Part Number: UCD90160 Tool/software: WEBENCH® Design Tools Hi, TI experts Where can I get the TI-Fusion-Digital-Power-Designer-7.2.5_Beta, as our project file is only support this version. Could you please help to provide it? Thank you.

  • Resolved

  • 9 months ago
  • Power management
  • Power management forum
Answered

• UCD90160: how to see i2c command of Fusion Digital Power Designer?

  

  Yoonsun Kim

  Resolved

  Part Number: UCD90160 I need to control ucd90160 by processor over i2c line. I checked that 'Fusion Digital Power Designer' polled values well. It will be very helpful If I can see the pm bus command and response data between SW and UCD90160. …

  • Resolved

  • 9 months ago
  • Power management
  • Power management forum

• UCD90160: UCD90160 problem generating same hex file

  

  stephen chu

  TI Thinks Resolved

  Part Number: UCD90160 When I generate the hex files to different directory ./output, ./output2. And I compare them. There are some differences close to the end of the file. the following shows only the differences, the left most number is the line number…

  • over 1 year ago
  • Power management
  • Power management forum

• UCD90160: logic controlled GPO failed somehow

  

  Henry Kang

  TI Thinks Resolved

  Part Number: UCD90160 Hi Team, is there any sequence or timing restriction for logic controlled GPO? or others limitation? we found that the GPO may fail to turn active when all of input signals are satisfied, but the GPO status can be changed through…

  • over 1 year ago
  • Power management
  • Power management forum
Answered

• UCD90160: Power dissipation and Formula for the values

  

  Jonathan Geronga

  Resolved

  Part Number: UCD90160 Hi Team, Our customer is requesting for the power dissipation for UCD90160RGCT and also the formula with the values. Thanks, Jonathan.

  • Resolved

  • over 1 year ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.