Search - TI E2E support forums

Search tips

Showing 608 results View by: Thread Post Sort by

MMWCAS-DSP-EVM: MMWAVE-DSP-EVM Boot Issues

Mark Southcott

TI Thinks Resolved
Part Number: MMWCAS-DSP-EVM This is using the same DSP board that was identified as faulty in this post: New tab (ti.com) . As TI and Mouser are no longer carrying this board I'm trying to find if there is a way to use the board and thought perhaps using…
- 7 months ago
- Sensors
- Sensors forum
RE: ADS8028: How to calculate the ADC error and compare the ADC accuracy with AMC7836?

Aaron Estrada

Hi Lucas! It sounds like you are trying to calculate the Total Unadjusted Error (TUE). I have linked a an application note that talks about how to calculate this error. The one thing to note is that the units should be the same values. So for example…
- over 1 year ago
- Data converters
- Data converters forum
RE: XTR115: XTR115 output current drift during IEC61000-4-6: Conducted Immunity test

Raymond Zhang1

Hi Darshan, This is proper connection for XTR115/XTR116/XTR117 2-wire 4-20mA transmitter. Please note the GND connection and Floating_GND node, which are not the same ground. In addition, the DAC8551's supply voltage in the reference design is powered…
- over 1 year ago
- Amplifiers
- Amplifiers forum

RE: LP-CC1312R7: wpantund initialization problem

Eren Gürtas

Resolved
Hi Marie, Thank you for your interest . I tested SimpleLink SDK v. 5.30 but wpantund gets stuck in the middle of the initialization. I tried to use wfanctl in anyway but when I try to get interface up wfanctl giving me timeout error. Error message of wfanctl…
- over 1 year ago
- Sub-1 GHz
- Sub-1 GHz forum
RE: ADS131M08: Error calculation

Cole Macias

Hello Sunney, I think we have some TI Precision Lab videos that you'd benefit from: The first video in ADC Specifications series (talks about INL, offset, and others) https://training.ti.com/ti-precision-labs-adcs-dc-spec The first video in ADC Error…
- over 1 year ago
- Data converters
- Data converters forum
RE: TPS54561-Q1: The Output voltage ripple is over 0.5% of VOUT

Henry Kou

Hi Tommy, While I take a look at the schematic, please fill out the quick start calculator attached. Thanks, Henry 0160.TPS54360-361FAMILY_CALC_TOOL_REVE.xls
- 6 months ago
- Power management
- Power management forum

RE: ADS131M04: Min/max electrical characteristics for uncertainties & precision calculation

Cole Macias

Resolved
Hello Gaunthier, Please refer to our TI Precision Labs video Statistics behind error analysis of ADC system https://training.ti.com/ti-precision-labs-adcs-statistics-behind-error-analysis In general it explains that most typical specifications fall into…
- over 1 year ago
- Data converters
- Data converters forum
RE: I think TI's Crystal cap. calcs for the TM4C129X are in error

Peter John

Roberto Romano said: Your crystal require a 7pF load capacitor, Not correct. 7pF is my crystal's SHUNT capacitance as per my original post. Thus your calculations that followed were in error. Roberto Romano said: From where you can see 18 = 32 ??? Using…
- over 9 years ago
- Arm-based microcontrollers
- Arm-based microcontrollers forum
RE: AM3352 dmesg error code (SR 1: curr=1112500, delta_v=-3822, calc=1108678, act=1112500, gain=27)

Bruno Bittner1

Miroslav Kiradzhiyski XID said: Hi James, Would you kindly explain what the SR 1 error message stands for? ( SR 1: curr=1112500, delta_v=-3822, calc=1108678, act=1112500, gain=27). Attached is the booting dmesg for your reference. Your reply will be highly…
- over 9 years ago
- Processors
- Processors forum

RE: LMX2492EVM: Inquiries

Danilo A.

Resolved
Hi Derek, We just received this update from our customer. I was able to connect to the tics pro software and now I am trying to work on the Python file of the RAMP CALC but as soon as I run it it shows me errors so I wanted to know how it can be used…
- over 1 year ago
- Clock & timing
- Clock & timing forum

Didn't find what you are looking for? Post a new question.

Ask a new question