Search tips
Showing 332 results View by: Thread Post Sort by
    Answered

  • ADS131M06: IBIS model

    Resolved
    Part Number: ADS131M06 Other Parts Discussed in Thread: ADS131M08 , Hi Experts, Please provide the IBIS model for "ADS131M06IPBS" if available and ok to share with our customer. Thank you. Best regards, Gerald
    • Resolved
    • Answered

  • ADS131M08EVM: Inaccurate voltage values getting read

    Resolved
    Part Number: ADS131M08EVM Other Parts Discussed in Thread: ADS131M08 , ADS8168 Hi, I am providing a known analog signal to the EVM to test it for its working. A sinusoidal of 1 Vpp, at 1kHz, I am able to get an output of ~-488 mV and 480 mV (see 1st…
    • Resolved

  • AM2432: SPI Transaction Delays

    Part Number: AM2432 Other Parts Discussed in Thread: ADS131M08 , Hello I am working on interfacing an ads131m08 energy meter chip to a Sitara AM2432. I have the SPI transaction being started on a falling-edge signal interrupt from the energy meter…

  • AM62-EVSE-DEV-PLATFORM: What energy meter was used in this design?

    TI Thinks Resolved
    Part Number: AM62-EVSE-DEV-PLATFORM Other Parts Discussed in Thread: MSP430F5132 , ADS131M08 , Hi, I wanted to know what energy meter was used in this design? I checked the block diagram and the schematic, but it looks like the AC line voltage is…
    • Answered

  • ADS1178: Accuracy

    Resolved
    Part Number: ADS1178 Other Parts Discussed in Thread: ADS131M08 Hi. I would like to know the accuracy of this ADC. Thanks in advance.
    • Resolved
    • Answered

  • ADS1218: Data improper when giving sine wave at analog inputs of ADS1218

    Resolved
    Part Number: ADS1218 Other Parts Discussed in Thread: ADS131M08 Hello, I am trying to read data from ads1218 ADC interfaced with Arduino Uno. When I have connected differential input (bridge: maximum 70 mV output )in AIN0 (+ve) and AIN1 (-ve), fosc…
    • Resolved
    • Answered

  • LM334: LM334M out ripple lead to inaccuracy for ADC read

    Resolved
    Part Number: LM334 Other Parts Discussed in Thread: ADS131M08 hi team, we're using your LM334M and ADS131M08 for our design as below, we set up LM334M Iout=36uA, when we have the load NTC =10K with 4 wire mode connected to JP5, we found that we couldn…
    • Resolved
    • Answered

  • RE: ADS131M04EVM: Failure in initialising of ADS131 & getting interrupt on DRDY pin

    Resolved
    Hi Dale, From ADSEVM, now i get correct response on next command. Now when i interface EVM with MCU, i am facing challenge in initialising. Below is my code flow: 1. Clock INit 2. GPIO Init 3. SPI init- 8Mhz,16bits per fame 4. ADC Init--ADC…
    • Answered

  • ADS1018: Suitable ADC required to monitor 3-phase AC Load Using Current Transformer

    Resolved
    Part Number: ADS1018 Other Parts Discussed in Thread: ADS1118 , , ADS131M04 , ADS131M03 , ADS131E04 , MSPM0G1107 , ADS131M08 , ADS131M06 Hi, We need to Monitor the 3-phase Load Current using three Current Transformer(CT) for each phase. We need SPI…
    • Resolved

  • PROCESSOR-SDK-AM64X: Parallel Capture mode vs Direct Input Mode AM64x/AM243x

    Part Number: PROCESSOR-SDK-AM64X Other Parts Discussed in Thread: AM2434 , SYSCONFIG , ADS127L11 , ADS131M08 Tool/software: Hello, Similar to this thread, https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1300144/processor-sdk…

Didn't find what you are looking for? Post a new question.