• State Resolved
  • Locked Locked
  • Replies 6 replies
  • Subscribers 30 subscribers
  • Views 339 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

PP-SALB2-EVM: what are the uses of PP-SALB2-EVM board.

Mukesh Prajapati
Prodigy 150 points
Part Number: PP-SALB2-EVM

Hi Ivan,

I have some queries below related to PP-SALB2-EVM board.

Q1. https://www.ti.com/lit/an/slaa952/slaa952.pdf shows speaker characterization using PP-SALB2-EVM board. So this board is used for only speaker characterization or there are other applications also?

Q2. What types of problems we might face if we are not using this board for speaker characterizations rather using the parameter provided by the speaker manufacturer.

Q3. What is the difference between speaker characterization done with and without  PP-SALB2-EVM board.

Best regards,
Mukesh Prajapati  

  • 0
    TI__Guru* 99135 points

    Hi Mukesh,

    1. PP-SALB2-EVM is mostly used for speaker characterization. It can also be used for algorithm verification in case you want to measure the actual excursion using a measurement laser attached to the learning board.
    2. There should be no problem if you use the vendor provided speaker parameters as long as all the information is correct and complete. These parameters define the model the algorithm uses to estimate the temperature and excursion.
    3. You may refer to Q2 above, but difference is just the means to obtain the speaker parameters.

    Best regards,
    -Ivan Salazar
    Applications Engineer

  • 0 in reply to Ivan Salazar
    Prodigy 150 points

    Thank you for the clear understanding.

  • 0 in reply to Ivan Salazar
    Prodigy 150 points

    Hi Ivan,

    Wanted to know exactly what all parameters are verified using the external board? For examples parameters like:

    1. Spl vs frequency
    2. Impeadance vs frequency
    3. Thd vs frequency
    Apart from these there are TS parameters.
    Best regards,
    Mukesh Prajapati.
  • 0 in reply to Mukesh Prajapati
    TI__Guru* 99135 points

    Hi Mukesh,

    SPL and THD are measured only with microphone, PP-SALB2-EVM is not required/used for these measurements.

    Impedance vs frequency is obtained as part of the speaker characterization by using the IV-sense data and the PP-SALB2-EVM processing; a model is fitted based on the test. This model is based on the same TS parameters you've mentioned.

    Best regards,
    -Ivan Salazar
    Applications Engineer

  • 0 in reply to Ivan Salazar
    Prodigy 150 points

    Hi Ivan,

    Thank for the explanation.

    Q1. So we will be only getting the real TS parameter or we will also get the offset between Theoretical and Real one?

    Q2. What are the other parameters we will get using PP-SALB2-EVM board?

    Best regards,

    Mukesh Prajapati

  • 0 in reply to Mukesh Prajapati
    TI__Guru* 99135 points

    Hi Mukesh,

    1. Not sure what you mean by theoretical and real TS parameters. During speaker char, the hardware (EVM and PP-SALB2-EVM) is used to obtain TS parameters; alternatively, TS parameters can be input directly from speaker char from its vendor. Either way, once speaker char parameters are input or obtained, you can see the comparison between measured and fitted impedance plots in PPC3 like the below:
    2. You basically get all the parameters from Characterization panel:

    Best regards,
    -Ivan Salazar
    Applications Engineer