• State
  • Locked Locked
  • Replies 12 replies
  • Subscribers 33 subscribers
  • Views 314 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

PCA9539: PCA9539

prabhu k
Prodigy 165 points
Part Number: PCA9539

Tool/software:

HI TI Team,

In my design we are using PCA9539DGVR I/O Expander and MCU (S32K144)
Please check below schematic for your reference.

I flashed an example code, But when I tried to capture the Signal Slave is not giving Acknowledge. please check below image of scope.

 

Can you please suggest working code(configuration settings)

  • 0
    Guru 299450 points

    What are the voltages you measure at pins 2, 3, 21, and 24?

    Can you show the I²C access on an oscilloscope?

  • 0 in reply to Clemens Ladisch
    Prodigy 165 points

    Hi Clemens,

    Thank you for your support, please check below reply:
    Voltages at pins 2 & 21----0V, pin3---3.7V, pin24--5V

    We soldered wires below marked points and captured on logic analyzer waveform

  • 0 in reply to prabhu k
    Prodigy 165 points

    please suggest working code and configuration settings(SDA,SCL & RST) pins---I2C interface.

  • 0 in reply to prabhu k
    Guru 299450 points

    What is the processor's I/O voltage? Where does the 3.7 V on the reset line come from?

  • 0 in reply to prabhu k
    TI__Mastermind 38303 points

    Hi Prabhu,

    The /RESET voltage is 3.7 V. This should not trigger a reset condition but the voltage is quite LOW. What voltage supplies are being used in the schematic. I see 5V logic, but it seems that the /RESET pin is pulled to something else. 

    Can you confirm that the SDA/SCL waveforms measured at the MCU are the same waveforms appearing at the PCA9539? 

    Regards,

    Tyler

  • 0 in reply to Clemens Ladisch
    Prodigy 165 points

    Hi Clemens,
    Processor IO voltage is 5V.
    Please check RST pin pullup with 10K--5V

  • 0 in reply to Tyler Townsend
    Prodigy 165 points

    Hi Tyler,

    RST pin pullup with 10K--5V

    Can you confirm that the SDA/SCL waveforms measured at the MCU are the same waveforms appearing at the PCA9539? 

    Both side same waveforms appearing.

  • 0 in reply to prabhu k
    Guru 299450 points

    The /RESET pin voltage is wrong. There should be nothing that pulls down this line. Do you have any pull-down resistors? Check for solder bridges.

    If the /RESET voltage is wrong, then the SDA/SCL voltages also might be wrong. Please use an oscilloscope.

  • 0 in reply to Clemens Ladisch
    Prodigy 165 points

    Hi Clemens,

    Both sides MCU & IO Expander side we are using 5VCC.

    There is no pulldown resistor on /RST pin

    What is the voltage on SCL/SDA & /RST pins ?

  • 0 in reply to prabhu k
    Prodigy 165 points

    Hi Clemens,

    still we are facing issue on : Slave is not giving Acknowledge.

  • 0 in reply to prabhu k
    TI__Mastermind 38303 points

    Hi Prabhu,

    I know the SPICE model looks to be accurate and that you are using the DGV package, but can you double check that the pinouts are all the same? 

    The square QFN and leaded packaging styles use different pinouts. 

    Any update on any solder bridges on the PCB? Do you have a picture of the PCB? 

    Do you have any analog waveforms of the signal? Can you use an oscilloscope rather than digital analyzer? It will help give a better picture of what is actually going on at the IO expander. 

    Regards,

    Tyler