• Threads 51548 Discussions
Texas Instruments (TI) Microcontrollers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search for content on other microcontrollers or ask technical support questions on the extensive portfolio of microcontrollers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM263P4-Q1: How to parse AM263P ROM Logs

    Part Number: AM263P4-Q1 Hi expert, Can you provide me the steps or tools necessary to parse ROM Logs in AM263P SoC.

  • [FAQ] AM263P4-Q1: How to lock blocks/sectors in flash to prevent erase/write operations

    Part Number: AM263P4-Q1 Other Parts Discussed in Thread: UNIFLASH , SYSCONFIG Hi TI Team, How can I protect blocks/sector against erases and writes.

  • [FAQ] AM2612-Q1: How to run AM261 SoC at 200MHz CPU Clock Frequency

    Hi TI team, How to configure AM261 SoC to run at 200MHz CPU Clock Frequency?

  • [FAQ] AM13E23019: Not able to connect the AM13x device . Error connecting target error -615

    Part Number: AM13E23019 Hi , When trying to connect am13x launchpad we get the following errors; CS_DAP_0: Error connecting to the target: (Error -615 @ 0x0) The target failed to see a correctly formatted SWD header. The connection to the target…

  • [FAQ] MSPM0G3519: MSPM0 EEPROM Emulation Usage - Calculation on Space Utilization and Equivalent Endurance

    Part Number: MSPM0G3519 Important note - Please note we only discuss memory space utilization and equivalent endurance here for the comparison. FEE method is a nice method to enable a wider range of data size configuration, and support some special…

  • [FAQ] AM13E23019: How to add FastRTS math functions to a project

    Part Number: AM13E23019 Other Parts Discussed in Thread: MATHLIB , SYSCONFIG Hi, I imported the adc_mcpwm_trigger project and tried to use the FastRTS (TMU) functions in this project by including the "fastrts_tmu.h" file as instructed in the document…

  • [FAQ] MSPM33C321A: How to transfer I2C mode from target to controller during run-time

    Part Number: MSPM33C321A The idea here is to reset and re-init the I2C module. Please find the example as following. Demo_i2c_target_to_controller_rw_multibyte_fifo_poll_LP_MSPM33C321A_nortos_ticlang.zip

  • [FAQ] AM13E23019: AM13E230x : Frequently asked ADC questions

    Part Number: AM13E23019 What are the most Common ADC Terms and their definitions? What operations can be performed in the ADC Post-Processing Block in hardware? What is the temperature range of operation for the ADC peripheral? What is the ENOB…

  • [FAQ] AM13E23019: How to enable the CSC mode in AM13E230x device? How to use UART bootloader to flash image to the device?

    Part Number: AM13E23019 Other Parts Discussed in Thread: SYSCONFIG Hi experts, I am using the AM13E230x device along with the mcu_sdk v26.0 Is it possible to enable a custom bootloader in TI AM13E230x? If so, how to enable and flash the custom…

  • [FAQ] AM13E23019: Is brownout reset supported on the AM13E230x devices and is it configurable?

    Part Number: AM13E23019 Hi experts, Is early brownout detection (with interrupt) possible? How to configure thresholds? "7.8.1 Power Management Unit (PMU): section in datasheet mentions "Brownout reset (BOR) supply monitor with early warning capability…

View FAQ threads