Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62Ax / AM62Px / AM62D-Q1 / AM62L / AM64x / AM243x Design Recommendations / Custom board hardware design - Drive Strength Configuration for SDIO and LVCMOS I/Os

    Part Number: AM625 Other Parts Discussed in Thread: AM62A7 , Tool/software: Hi TI Experts, I have the below query AM62A7: How can we change the drive strength of the SPI interface AM625: How to change the drive strength of the ethernet interface…

  • [FAQ] TDA4VL-Q1: ECC Testing Procedure for Inaccessible RAM IDs

    Part Number: TDA4VL-Q1 Tool/software: Does the SDL ECC test cover error injection tests on the inaccessible endpoints? If not, what is the testing procedure for these endpoints?

  • [FAQ] TDA4VH-Q1: ECC Testing Procedure for Inaccessible RAM IDs

    Part Number: TDA4VH-Q1 Tool/software: Does the SDL ECC test cover error injection tests on the inaccessible endpoints? If not, what is the testing procedure for these endpoints?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP: MCU_PORz input slew rate

    Part Number: AM623 Other Parts Discussed in Thread: AM625 Tool/software: Usually add RC filter on RESET signal to anti noise, but the slew rate requirement of RESET signal on AM62x datasheet is quite sharp, on customer board it is about 10V-100V/ms…

  • [FAQ] AM623: MMC0 HS200 slew rate

    Part Number: AM623 Tool/software: #1. Did not find MMC0 HS200 slew rate data in datasheet timing section, so section 7.8.6 LVCMOS Electrical Characteristics data applies? #2. The Min vale: 18f or 1.8E+6, the two value are quite different, 18f=18x200MHz…

  • [FAQ] Guideline on the Initial Software Post on E2E

    When posting a new software inquiry on the TI E2E forum, please follow this guideline for the initial post. Describing the Problem Using the following list of questions as the template, copy and paste the questions to your post, and answer them if…

  • [FAQ] AM67A: Enabling CSI2 sensors via fusion board on AM6x

    Part Number: AM67A Other Parts Discussed in Thread: SK-AM69 , SK-AM68 , AM67 , SK-TDA4VM Tool/software: How can I enable CSI2 sensors via fusion boards such as Arducam V3Link or fusion 1 daughter board (EVM577PFUSION-V1-0)?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP : Enabling spread spectrum core clock on PRUSS

    Part Number: AM625 Tool/software: Dear all, In AM625: Help setting PRUSS clock to 333MHz on AM6254 I was able to set my AM625's PRU to run at 333MHz and confirmed it with a scope. Now I'd like to understand whether spread spectrum can be enabled…

  • [FAQ] TDA4VM: TDA4VM/TDA4VL/TDA4AL/TDA4VH/DRA821: Custom DDR Memory Mapping for Vision Applications on Jacinto SoCs

    Part Number: TDA4VM Tool/software: What are the changes involved to reduce the DDR instances and run the demos using 2GB DDR configuration?

  • [FAQ] AM644x / AM642x / AM641x / AM243x (ALV) Design Recommendations / Custom board hardware design – common queries for PMIC TPS65219 and TPS65220

    Part Number: AM6442 Other Parts Discussed in Thread: TPS65220 , TPS65219 , TPS6521905 , TPS65215 , AM2434 , AM6421 Tool/software: HI Board designers, I am designing my board using TPS65219 or TPS65220 Are there some common recommendation or observations…

View FAQ threads
  • Threads 197786 Discussions