Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VM: OpenVX Host on R5F and node Target on A72 (Linux)

    Part Number: TDA4VM How to run OpenVX Host on R5F and a node to run on A72 (Linux) as target?

  • [FAQ] AM623: Decoupling caps on CAP_VDDSx

    Part Number: AM623 Champs, Customer's asking what will happen if the decoupling caps on the CAP* nets below are not installed correctly? Will the device's behavior be well defined in this case (i.e. fail to boot etc) or would it be more sporadic based…

  • [FAQ] AM6x: Yocto build "hangs" for hours with no progress - What's going on?

    (applicable to all TI Sitara and Jacinto devices such as AM62x, AM62Ax, AM64x, AM65x, and so on) Symptoms When doing a Yocto build as per SDK instructions for example of the SDK default image like this... MACHINE=am62xx-evm bitbake -k tisdk-default…

  • [FAQ] AM62A3-Q1: The MISO and MOSI of the SPI

    Part Number: AM62A3-Q1 Hi TI expert, The SOC AM62A define the standard SPI interface by SPI_CS, SPI_CLK, SPI_D0, SPI_D1. If our slave device need to get MISO and MOSI data line, how will we used the D0 and D1 data line. Dose it programable? Can…

  • [FAQ] AM625/AM623 Custom board hardware design – Reading DEVICE_ID and Unique SOC (CPU) ID

    Other Parts Discussed in Thread: AM62L I have the below queries regarding the DEVICS_ID Is there a device ID available that I can read? Can you guide me how to read the device ID? Is the ID unique for each device? Is there an ID that is unique…

  • [FAQ] AM625: Crystal drive strength specifications

    Part Number: AM625 Hello, Do we have a specification on the max drive strength/ power that AM625 can drive for both the HF crystal as well as 32 KHz oscillator? I didn't see it specified in the data sheet and customer wants to make sure they're within…

  • [FAQ] How to synchronize the PRU IEP timer with Linux system time?

    I am using a Sitara processor with a Linux core, a time sync router, and a PRU subsystem (AM62x, AM64x, AM65x). I want to synchronize the Linux system time with an IEP timer in the PRU subsystem. How do I do it? We will use AM64x for this example, but…

  • [FAQ] PROCESSOR-SDK-J7200: How to change/generate the “Eth” configuration for MCAL Ethernet Application from one core to other core.

    Part Number: PROCESSOR-SDK-J7200 Other Parts Discussed in Thread: DRA821 , DRA829 , SYSCONFIG How to change/generate the “Eth” configuration for MCAL Ethernet Application from one core to other core.

  • [FAQ] AM6412: AM64x SoC power supply slew control for 3.3V_SYS using load switch

    Part Number: AM6412 Other Parts Discussed in Thread: TPS65219 Hi team, I'm helping my customer design the power part of AM64. For the power supply slew rate control part, it says the slew rate should be controlled under 18mV/us. How should we set…

  • [FAQ] Redundant boot from eMMC boot partitions on AM62x

    1. booting from eMMC boot partition vs UDA partition It is recommended to use eMMC boot partition for user's BootLoader (BL) - eMMC boot partition is designed for bootloader user case - it is possible to write-protect boot0/boot1 as necessary - eMMC boot…

View FAQ threads
  • Threads 198909 Discussions