Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] How do I create a SYS/BIOS based CCS project for AM335x/AM437x Cortex A8/A9 core?

    Part Number: AM3359 I need to build a CCS project using SYS/BIOS for AM335x/AM437x devices. How can I get started?

  • [FAQ] TDA4VM: How to move DMPAC to mcu2_0 or other R5F core?

    Part Number: TDA4VM In the PSDKRA, DMPAC is allocated to the core mcu2_1. This article explains how it can be moved to other R5F core, by providing an example of moving it to mcu2_0.

  • [FAQ] J721EXSOMXEVM: How to change Linux kernel page size from default 64K in the SDK to 4K?

    Part Number: J721EXSOMXEVM Hi, support team My customer has the questions as follow: for sdk download form www.ti.com/.../PROCESSOR-SDK-LINUX-J721E I found kernel config board-support/linux-5.4.106+gitAUTOINC+023faefa70-g023faefa70/arch/arm64…

  • [FAQ] AM6548: CTRLMMR_WKUP_JTAGID register value for SR2.1

    Part Number: AM6548 Section "1.6 Device Identification" in the TRM describes the CTRLMMR_WKUP_JTAGID register values for SR1.0 and SR2.0, but not for SR2.1. What is the CTRLMMR_WKUP_JTAGID register value for SR2.1? Is it the same as SR2.0? Best…

  • [FAQ] TDA4VM: How to provide different set of parameters in replicated node, like two look up table for LDC module

    Part Number: TDA4VM When a node is replicated in the OpenVX, the parameters passed to the node instance0 will reused for all the replicated node. Typically only input and/our output images are replicated in application to provide different instance of…

  • [FAQ] Are there sample CCS projects to help me start TI-RTOS or bare-metal development for AM335x/AM437x devices?

    Part Number: AM3358 I’m going to do TI-RTOS / bare-metal development for AM335x/AM437x devices. Does TI offer sample projects which can help me get started? For example, a sample project on how to blink an LED or how to use UART for debug tracing would…

  • [FAQ] TDA4VM: EdgeAI Sep Webinar: DIY home-monitor edge AI box with $199 starter kit enabling 8 TOPS hardware-accelerated deep learning

    Part Number: TDA4VM In this webinar, follow along as we build a simple, do-it-yourself (DIY) edge AI box application . Using the new $199 SK-TDA4VM edge AI starter kit—enabling 8 TOPS of hardware-accelerated deep learning—you can create an application…

  • [FAQ] PROCESSOR-SDK-J721E: eDP firmware responds wrongly to some messages and thus causes display incompatibility.

    Part Number: PROCESSOR-SDK-J721E Hello, I'm trying to analyze instability in display startup, that we observe with some, but not all, displays, both with linux drm drivers and with sdk r5 drivers. Thy symptom is: not all displays turn on and show…

  • [FAQ] TDA4VM: U-Boot Changes in SDK 8.0 Vs 7.3

    Part Number: TDA4VM There are few changes w.r.t U-Boot from 7.3 SDK to 8.0 SDK. List out the important changes.

  • [FAQ] DRA821U: DRA829 : Guide to Do Board specific modifications for CPSW 5G/9G

    Part Number: DRA821U What changes are required to do board specific modifications for CPSW 5G/9G in enet-lld and EthFW ?

View FAQ threads
  • Threads 198001 Discussions