This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Part Number: DRV8880
I have an product that I'm trying to find the "right" settings for the DRV8880. I have the DRV8880EVM and was testing different conditions with my motor (see attachments). I'm using a custom application to generate the control signals to the DRV8880 and the currrent code does not have any acceleration controls, just PWM frequency. The prior prototype was based on the DRV8825 and the last PWM setting yielded ~4kHz pulse rate (see attached scope plot).
I was using a different motor and slide for the DRV8825 prototype but by sending this step and varying the mode pins (using AutoTune) the motor just whines and does not move. Using the EVM and GUI connected to the new motor/slide arrangement I can get the same results but by adjusting the starting speed, stopping speed, and acceleration I can make the motor move but at this point I'm just making random uneducated guesses.
The motor doesn't have to move fast but with a 6" travel I don't want the operator to have to sit and twiddle their thumbs while the motor moves. The basic operation is that the motor moves a stage that exits a chamber. The operator then places a sample on the stage, pushes GO, and the stage retreats back inside the chamber where it will make a series of small moves (~15mm) back and forth for several hours.
I don't see any faults when the motor whines and I'm currently using a bench top power supply set at 24V and a current limit of 1.1A. For the most part the power supply sits at supplying ~350mA.
I'm hoping that someone can help me learn the best way to adjust and set the appropriate parameters as I was hoping that by switching to the DRV8880 and using AutoTune I wouldn't have to become a motor expert. We can add code to apply some acceleration parameters to adjust the PWM but of course if that's not needed it's preferred not to add additional work.
Thank in advance for the help and education!
What starting, stopping, steps, acceleration, and steps to move settings have you tried with the EVM and GUI?
How many turns of the lead screw are required to move 6 inches?
Rick DuncanMotor Applications Team
We are glad that we were able to resolve this issue, and will now proceed to close this thread.
If you have further questions related to this thread, you may click "Ask a related question" below. The newly created question will be automatically linked to this question.
In reply to Rick Duncan:
I've been playing more with the GUI today in between watching some football and trying to not work so much! I should have saved the settings but I started using full steps and found that when using full steps everything seemed to be more sensitive to changes. I'll have to go back and see what I had but right now I'm experimenting with 1/4 step and I have the following settings:
When I was at full step I was having trouble setting target speed more than ~4500.
The lead screw is "2mm" but it doesn't appear to be trapezoidal like I thought it would be so it might just be a standard 2mm pitch screw? With the settings in this screen shot 40,000 steps moves the stage ~100mm
I don't have a current probe for my scope (just too damn expensive but it would be nice to have one now) but I could check some things if needed.
The current settings seem to be OK but I'm in a learning phase now and trying to determine how best to approach this and what kind of reasonable speed I can get out of this system. Right now I've just been poking around and changing settings on a trial and error basis.
I forgot to mention that this system will have a very light load, under 0.5lbs.
In reply to George Ioakimedes:
As a reference point I changed back to Full Step and even with these setting I'm not able to move the stage.
I did have some combination of setting that allowed Full Step to work before but I foolishly didn't write them down or take a screen shot.
Yes, the motor did not move and only whined at me!
Here is a combination of settings that almost work using full step. My method for testing is that I get the motor moving and then find a number of steps that give me a fair amount of travel. I then adjust settings while in reciprocal mode until I start to hear noises or the motor doesn't move. With some additional experimenting I found the following combination of settings to yield good speed as well as low current (~200mA/24V). My tests are with "no load" (meaning it is the factory slide from Velmex with nothing added).
Here is an additional 1/4 Step plot and I'll test more with Full Step later this morning.
Just wanted to post an initial Full Step settings experiment. With these settings the stage moves well but if I change the start speed to 2000 the stage stops moving. There's more experimenting to do but I'm still a bit unsure as to why the starting speed seems to matter so much.
Thanks for the analogy, that helps. The motor is this one but I don't see anything about speed. Looking at the GUI differences I see that the 1/4 Step is roughly 4x what I found with Full step so I guess things are making more sense now. I see that this motor has 11.2mH which seems like a lot and I imagine that this is greatest impact on the acceleration and speed settings. Looking back at the specs on the initial motors I was testing I see they only had 2.0mH and 4.5mH so if I'm right that would explain why things "seem" more difficult to dial in now.
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.