Answered

• RE: DS100KR800: signal integrity is reduced by the repeater

  

  Lucas Wolter

  Resolved

  Hi Robin, Great, I'm glad you were able to resolve the issue with Drew's feedback. Thank you for confirming the issue is resolved. Best, Lucas

  • 6 days ago
  • Interface
  • Interface forum
Answered

• DS100KR800EVK: DS100KR800

  

  Robin V.

  Resolved

  Part Number: DS100KR800EVK Other Parts Discussed in Thread: USB2ANY , , LMH1218 , DS100KR800 Hello, I have installed SigCon Architect With RTE v2.0.0.8 in order to use it with DS100KR800EVK throught USB2ANY. There is only one device model listed LMH1218. …

  • Resolved

  • 4 months ago
  • Interface
  • Interface forum

• DS100BR410: Differences between the DS100BR410 repeater, the DS100KR800 repeater, and the DS100KR401 repeater.

  

  James Gassner

  TI Thinks Resolved

  Part Number: DS100BR410 Tool/software: Good afternoon, What are the main performance differences between the three PNs listed in the thread title? I see that the 401 and 800 devices each have 8 channels where the 410 only has 4 and I noticed the pinouts…

  • 3 months ago
  • Interface
  • Interface forum
Answered

• DS100KR800: DS100KR800 SMBUS slave mode control register

  

  Adrian Burr

  Resolved

  Part Number: DS100KR800 when using this device in SMBUS slave mode are the control register outputs automatically set to their defaults and working at reset i.e VOD and DEM OR do we need to enable slave register control at 0x06 for the device to start…

  • Resolved

  • over 1 year ago
  • Interface
  • Interface forum

• DS100KR800: Bypass mode?

  

  Shawn_Wang

  Part Number: DS100KR800 Hi team My customer is using DS100KR800 for FPGA SERDES port between two boards and they want to know if DS100KR800 is supporting Bypass mode? (FPGA SERDES -> DS100KR800#1) -> 2m 10G cable -> (DS100KR800#2 -> FPGA SERDES) …

  • over 2 years ago
  • Interface
  • Interface forum

• DS100KR800: Whether it need two sides CPUS to be configured to 10GBASE-KR mode to make the link to be ok with DS100KR800

  

  Frank Xiao

  Part Number: DS100KR800 Hi team, My customer is using the DS100KR800 now, the block diagram below. Two sides CPU can support KR mode. Whether it need two sides CPUS to be configured to 10GBASE-KR mode to make the link to be ok. Thanks.

  • over 4 years ago
  • Interface
  • Interface forum

• DS100KR800: he difference between the 10G mode and 10G-KR mode

  

  Frank Xiao

  TI Thinks Resolved

  Part Number: DS100KR800 hI team, We want to check the difference between the 10G mode and 10G-KR mode? Whether configure pin 21 mode resistor is fine? Thanks.

  • over 3 years ago
  • Interface
  • Interface forum

• DS100KR800: Does the DS100KR800 support the AN protocol? Does the DS100KR800 support 10.9375GHz?

  

  Seasat Liu

  TI Thinks Resolved

  Part Number: DS100KR800 1.Does the DS100KR800 support the AN protocol? 2. CTM backplane should run the HIGI protocol, and the maximum rate will reach 10.9375G. Can the KR800 support it? Or must use DS125KR820?

  • over 5 years ago
  • Interface
  • Interface forum

• DS100KR800: he DS100KR800 AD[3:0]、ENSMB、READ_EN、MODE high level & low level spec & sampling & holding time spec

  

  Frank Xiao

  TI Thinks Resolved

  Part Number: DS100KR800 Hi team, My customer want to check the DS100KR800 AD[3:0]、ENSMB、READ_EN、MODE high level & low level specs. Whether we have sampling & holding time spec for the level? Thanks.

  • over 5 years ago
  • Interface
  • Interface forum

• DS100KR800: Whether the device DS100KR800 has pin delay requirement when do CAD design?

  

  Frank Xiao

  TI Thinks Resolved

  Part Number: DS100KR800 Hi team, Whether the device has pin delay requirement when do CAD design? Thanks.

  • over 5 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.