• DS91M125: Question of Datasheet Information

  

  Richard Williams

  TI Thinks Resolved

  Part Number: DS91M125 Tool/software: I would like clarification of the output pins for the DS91M125. Page 3 of the datasheet (SNLS290C) there is a Logic Diagram and a Pin Descriptions table. The diagram shows pin B0 as an inverting pin and pin A0 as…

  • over 1 year ago
  • Interface
  • Interface forum

• DS91M125: Can one of the driver output be left open with enable pin active?

  

  Arun Patil

  TI Thinks Resolved

  Part Number: DS91M125 Tool/software: Hello, We have a system where LVDS Driver output signal has Vcm = 2.1V with Vid = 1.1V (each LVDS line swings from 2.1V to 2.65V with respect to ground when connected to a single 120 ohm input terminated LVDS receiver…

  • over 1 year ago
  • Interface
  • Interface forum

• DS91M125: Max PCB Trace Length

  

  Jack Zhang

  TI Thinks Resolved

  Part Number: DS91M125 Hello, I am working on a backplane design that interfaces with a plug-in card that generates an M-LVDS clock output. The backplane will bus the signal to several payload slots. I would like to know if TI has an recommendation for…

  • over 2 years ago
  • Interface
  • Interface forum

• DS91M125: 11 outputs with 4 DS91M125s

  

  Yusuke Mukuno

  TI Thinks Resolved

  Part Number: DS91M125 Other Parts Discussed in Thread: SN65LVDS104 Hi Expert, My customer have a question. Can they configure for 11 M-LVDS outputs with 4 DS91M125s, like as the following figure? Thanks Muk

  • over 5 years ago
  • Interface
  • Interface forum
Answered

• DS91M125: IBIS Model

  

  Steve Widener

  Resolved

  Part Number: DS91M125 Other Parts Discussed in Thread: SN65MLVD040 I'm not able to find an IBIS model for the DS91M125 on the ti.com website - do we have one available?

  • Resolved

  • over 5 years ago
  • Interface
  • Interface forum
Answered

• DS91M125: Can three drivers work at the same time?

  

  Sherry Liang

  Resolved

  Part Number: DS91M125 Other Parts Discussed in Thread: SN65LVDS104 Dear team, My customer hopes that DE0/DE1/DE2 are high at the same time, which means three drivers work at the same time. Is it feasible? In addition, this device's frequency is 125MHz…

  • Resolved

  • over 5 years ago
  • Interface
  • Interface forum

• SN65LVDS22: MLVDS buffer or repeater, similar with SN65LVDS22 or DS90LV001

  

  Ken Zhang

  TI Thinks Resolved

  Part Number: SN65LVDS22 Other Parts Discussed in Thread: DS90LV001 , DS91M125 Tool/software: Hi, Are there a MLVDS buffer or repeater ICs? 1 channel and 2 channels are preferred? SN65LVDS22 and DS90LV001 are for LVDS, not MLVDS.

  • 5 months ago
  • Interface
  • Interface forum

• SN74HC74: D Flip-flop output as LVDS clock signal

  

  Arun Patil

  TI Thinks Resolved

  Part Number: SN74HC74 Other Parts Discussed in Thread: DSLVDS1047 , SN74LVC541A , DS91M125 Tool/software: We came across an instrument that has SN74HC74PWR, the two D flip-flips as divide by two counters cascaded, the first counter is driven by 4 MHz…

  • over 1 year ago
  • Logic
  • Logic forum

• Interfacing M-LVDS and LVDS

  

  Michael Woi

  Other Parts Discussed in Thread: DS91M125 , DS90LV032A One question: Can I connect the output of an M-LVDS driver/repeater (DS91M125) to an LVDS receiver (DS90LV032A)? I've been searching through the site and documents, but haven't found a definitive…

  • over 10 years ago
  • Interface
  • Interface forum

• TCAN1057A-Q1: CAN Star Topology change to Linear Topology and spurious noise issues

  

  Arun Patil

  TI Thinks Resolved

  Part Number: TCAN1057A-Q1 Tool/software: Hello Eric, As suggested by your team member, Ms Amy, this new thread is being opened for the CAN portion of the following post. https://e2e.ti.com/support/interface-group/interface/f/interface-forum…

  • over 1 year ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.