TI E2E support forums
Menu
Search through millions of questions and answers
User
Menu
Search through millions of questions and answers
User
E2E™ support forums
Forums
Amplifiers
Audio
Clock & timing
Data converters
DLP® products
Interface
Isolation
Logic
Microcontrollers
Motor drivers
Power management
Processors
RF & microwave
Sensors
Site support
Switches & multiplexers
Tools
Wireless connectivity
Archived forums
Archived groups
Technical articles
Analog
Automotive
DLP® technology
Embedded processing
Industrial
Power management
0
TI training
Tech days
Online training
Live events
Power Supply Design Seminar
Getting started
More
Cancel
简体中文
Search tips
Showing 14 results
View by: Thread
Post
Sort by
Relevance
Oldest to Newest
Newest to Oldest
Mike Wu1
10 months ago
MSP low-power microcontrollers
MSP low-power microcontroller forum
MSP430FG438: About the DAC Calibration
TI Thinks Resolved
Part Number:
MSP430FG438
Hi, My customer has the following question, please help to provide comments. 1. After executing DAC calibration, why the parameter are not all the same after each round of calibration ? 2. About the a, b value in the page...
Dietmar Walther
10 months ago
MSP low-power microcontrollers
MSP low-power microcontroller forum
RE: MSP430F6723: Auxiliary Supply System and Low Power Modes
Hi Maxim, do you have considered AUXPMM1 and AUXPMM2 in your application design? Please find here the link to the corresponding ERRATA:
Winter Yu
over 2 years ago
Simulation, hardware & system design tools
Simulation, hardware & system design tools forum
RE: WEBENCH® Tools: Amplitude Controlling of Sinewave from 0.4VAC to 6VAC at fixed Freq. 400Hz using MCU & POT
Hello,
MSP430FG438
has the 12-bit DAC module, you can use it to generate the signal wave that you want. You can find the DAC example code at below link for reference. This example code is using DAC12 outputs a 16 Step Ramp with 1 sample/sec. You need...
Clemens Ladisch
over 4 years ago
MSP low-power microcontrollers
MSP low-power microcontroller forum
RE: How much is the deviation of the internal clock of MSP430FG438?
The FLL tries to adjust the DCO up or down so that there are 122 ticks of the (divided) DCO clock between two ticks of the reference clock. The two clocks are not exactly synchronized, so it is possible that you get 121 or 123 ticks, and the resulting...
DJ-NG
over 3 years ago
MSP low-power microcontrollers
MSP low-power microcontroller forum
RE: MSP430F67471: temperature sensor calibration
Thank you for the information. We understand, the tolerance for single-point calibration is not specified. But what about the tolerance of the two reference values stored by TI in the TLV block? If we use them, what is the accuracy of the slope of the...
Antonio Ceci
over 8 years ago
MSP low-power microcontrollers
MSP low-power microcontroller forum
Msp430fg438 Uart programmation
Hello to everyone, I'm new of the MCU's world so I wonder if you can help me on this topic. For my graduation paper on aerospace engeneer i'm developing a test board for space solar cells with an
msp430fg438
. The purpose is to get th voltage...
Antonio Ceci
over 8 years ago
MSP low-power microcontrollers
MSP low-power microcontroller forum
MSP430FG438 Uart Problem
Hi to everyone, I resolved my problems with the uart protocol, but one other rised up. I setted up my micro with this routine: When from the RXBUF0 it receieves the letter G, it starts smpling from the adc. My problem is that it do that indefenetevly...
Shrikant Lokhande
over 8 years ago
MSP low-power microcontrollers
MSP low-power microcontroller forum
MSP430FG438 documentation required
Hi all, I intended to use
MSP430FG438
in one of my application for the first time, where I required to use ADC and UART modules. I have searched for the documentation where it will give thorough information about interfacing and coding of MSP but...
Kazeem Omidiji
over 9 years ago
MSP low-power microcontrollers
MSP low-power microcontroller forum
Unable to execute driver error MSP430FG438
Was wondering if anybody could help me figure out a problem I am having when I try to download my program onto my chip, I keep getting an error "Unable to execute driver error" with a green bar on "OOFFFF" stack inside the disassembly...
James Evans
over 3 years ago
MSP low-power microcontrollers
MSP low-power microcontroller forum
RE: MSP430F6726: Implementation of a Single-Phase Watt-Hour Meter
Hello Pavel, EDIT: I didn't read past your first error. You already did this, and I didn't notice. Pavel Hristov We tried adding the following lines in io.h #elif defined(__ MSP430F6726 __) #define __MSP430_6726__ For your first error...
>
Didn't find what you are looking for? Post a new question.
Ask a new question