TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel

Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed the week of November 23.



Search tips
Showing 12,575 results View by: Thread Post Sort by
  • RE: TMS320F280025: TMS320F280025 Single-Shunt PMSM Compressor Motor Control – Current Sensing Instability, ESMO Accuracy, and Vibration Issues

    Navaneeth Kumar
    Navaneeth Kumar
    Hi @venkata Genatco Thank you for the suggestions. We have tested the motor in no-load condition and were able to reach up to 320 Hz electrical frequency without any issues. The estimated angle remains stable and motor operation is smooth throughout…
    • 5 months ago
    • C2000™︎ microcontrollers
    • C2000 microcontrollers forum
  • RE: CC1311P3: CC1311P3 unable to decode 2-FSK signal at 19.2 kSps with ±2 kHz deviation

    Theiv B
    Theiv B
    Hi Daniel, We implemented the suggested fix and performed further validation. However, we did not observe any improvement in the intermittent data loss issue. As an additional mitigation attempt, we implemented an RX re-synchronization mechanism after…
    • 5 months ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • Answered
  • RE: LMK1C1103: Distribute clock to 9 units using clock buffer like LMK1C1103

    vicente flores prado
    vicente flores prado
    Resolved
    Hi Alessandro, Not yet. If you need a device with a low tempco (propdelayvariation/temp) we don't spec this for almost all of our devices except the RF buffers such as LMX1906-SP. You can estimate the tempco given the prop delay - overall the tempco across…
    • 9 months ago
    • Clock & timing
    • Clock & timing forum
  • IWRL6432WMOD: IWRL6432WMOD: Mapping simplified uDFP settings to exact radar chirp parameters

    Peter Bader
    Peter Bader
    Part Number: IWRL6432WMOD Other Parts Discussed in Thread: IWRL6432AOP Hi TI Support Team, I am currently evaluating both the IWRL6432WMOD and IWRL6432AOP radar modules for our application and need some insight into the uDFP settings. While I can…
    • 5 months ago
    • Sensors
    • Sensors forum
  • Answered
  • CC2745R10-Q1: How to choose UART interrupt (NVIC) priority relative to BLE stack and RTOS tasks

    snail leo
    snail leo
    Resolved
    Part Number: CC2745R10-Q1 Hi TI team, We are developing on the CC2745 (Cortex-M33, SimpleLink Low-Power F3 SDK) and need to configure the UART peripheral interrupt priority correctly. What we want to achieve We want the UART RX/TX interrupt to:…
    • Resolved
    • 3 months ago
    • Bluetooth®︎
    • Bluetooth forum
  • CC1311P3: CC1311P3 Frequency Error Above 430 MHz with Custom Overrides & Custom configuration

    Theiv B
    Theiv B
    TI Thinks Resolved
    Part Number: CC1311P3 We are working with the CC1311P3 device in proprietary RF mode and observing a frequency error when operating above 430 MHz. And, we are using a custom CMD_PROP_RADIO_DIV_SETUP_PA configuration with overrides specifically for operation…
    • 7 months ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • AWRL6844EVM: mmWave Evaluation board configuration

    Ati Haj
    Ati Haj
    Part Number: AWRL6844EVM Other Parts Discussed in Thread: AWR2944PEVM , AWRL6844 , AWR6843 , IWR1843 , AWR1843 , AWR2944 , IWR2944 , AWR2544 Hi, I am trying to configure the AWRL6844EVM board for a preferred detection range. The tools I am using are…
    • 6 months ago
    • Sensors
    • Sensors forum
  • TRF1305C2: looking for RF differential signal to Single ended Signal conversions amplifier

    Maharajan P
    Maharajan P
    TI Thinks Resolved
    Part Number: TRF1305C2 Other Parts Discussed in Thread: LMH5401 Dear Team , I am planning to use the following part "TRF1305C2" in my design, My design requirement is to Convert a RF differential signal to Single ended Signal. but in this part's…
    • 4 months ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • RE: REF30E: Schematic Review

    Andrew Li
    Andrew Li
    Resolved
    Hi Tilden, I do not have a specific capacitor PN in mind, but in general, most ceramic capacitors fall in the 10mΩ to 500mΩ range. As a general rule of thumb, we can look at the ESR at 10kHz for REF30E since this is one decade away from the rough estimation…
    • 2 months ago
    • Power management
    • Power management forum
  • Answered
  • RE: LMK04828BEVM: Settling Time For the Clock

    vicente flores prado
    vicente flores prado
    Resolved
    Hi Ajmal, The analog settling time is dependent on a variety of factors including loop bandwidth, frequency, charge pump current, etc. A good estimation for lock time is 4/LBW (loop bandwidth) Given LMK048xx or LMK04832 family are not used for frequency…
    • over 1 year ago
    • Clock & timing
    • Clock & timing forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question