Search tips
Showing 37 results View by: Thread Post Sort by

  • TLK106L: SMI does not work reliably

    Part Number: TLK106L Other Parts Discussed in Thread: TLK106 Dear TI-Team! We have a problem with the TLK106 similar to these forum requests: (1) TLK105 / TLK106 in Ethercat-network doesn't start at temperatures over 35°C - Interface forum - Interface…

  • TLK106: Using TLK106 instead of TLK106L for EtherCAT - Channel 0 does not respond

    TI Thinks Resolved
    Part Number: TLK106 Other Parts Discussed in Thread: , AM4377 Hello all, I'm working with a device which uses 2x TLK106L and an AM4377 to run two EtherCAT ports. Due to the supply chain issues I am trying to use TLK106 instead of TLK106L. To my understanding…

  • TLK106L: TLK106L vs TLK105L compatibility

    TI Thinks Resolved
    Part Number: TLK106L Other Parts Discussed in Thread: TLK105L , , TLK106 I had a question on the TLK106L. I’m using the TLK106 PHY chip on my board .The datasheet is generic , and also applies for TLK105L. The TLK106L works at maximum temperature of…

  • RE: TLK106L: TLK106L ESD issue

    Hello Yulei, We have a hardware rollover document listing the hardware differences in between DP83822 and TLK106L: www.ti.com/.../snla262.pdf For software, there are some new registers in DP83822 and there are some registers that overlap with TLK106L…

  • TLK106L: UPDATE: TLK106L: FCS errors on receiving side for PHY sourced frames

    TI Thinks Resolved
    Part Number: TLK106L Other Parts Discussed in Thread: TLK106 , TLK105 Hi Rob, original issue seems to be locked, so I provide update in this new issue. I attached to the issue: 1) Quartz specs 2) Ethernet schematics 3) Register dump when PHY experience…

  • TLK106L: ethernet communication not stable

    TI Thinks Resolved
    Part Number: TLK106L Hi, We are having the same stability problems with TLK106L Ethernet PHY as described in here : Since we have exactly the same hardware configuration, Related to this topic we have two questions : One confusing point in the Thread…

  • TLK106L: strange TX waveform

    Part Number: TLK106L Other Parts Discussed in Thread: DP83822I , TLK105L Hi! We have an issue with the ethernet communication over the TLK106L. Our System works in normal operation. We cyclically ping the TLK106L. If we turn the ETH-Link off and on, it starts…

  • TLK106L: FCS errors on receiving side for PHY sourced frames

    Part Number: TLK106L Other Parts Discussed in Thread: TLK106 Hi ! We are using TLK106L as a PHY together with STM32F407 MCU. After several hours after PHY reset number of FCS errors for frames transmitted by PHY is rising from zero to 10-15% of total…

  • TLK106L: ethernet communication not stable

    TI Thinks Resolved
    Part Number: TLK106L Other Parts Discussed in Thread: TLK106 , DP83822I In my design I use TLK106L in RMII connection. I have a "not stable" behaviour during ping test between my board and the Personal Computer I use for test. Please note that…

  • TLK106L: Powerlink interface NOT stable using FPGA, Two Ethernet PHY

    Part Number: TLK106L Our application implements a Powerlink interface, with the following characteristics: FPGA, Cyclon V, with Powerlink IP two Ethernet posrts with TLK106L, both configured in RMII mode One oscillator @ 50MHz configured as suggested…

Didn't find what you are looking for? Post a new question.