Search tips
Showing 36,956 results View by: Thread Post Sort by

  • TMDS181: The bug of EVM has removed or not

    TI Thinks Resolved
    Part Number: TMDS181 Tool/software: Hi team, I saw the users guide of TMDS181 (sllu228a): https://www.ti.com/lit/ug/sllu228a/sllu228a.pdf There is a description below. Have this bug fixed in new GUI already? Regards, Hayashi

  • INA333: EVM-Output voltage has large ripple

    TI Thinks Resolved
    Part Number: INA333 Other Parts Discussed in Thread: TINA-TI Hi, Recently, I tried few experiments by using Eval board: INAEVM-MSOP8 along with the INA333. In order to emulate the load cell (whose wheatstone bridge nominal resistance is 360 ohm) and…

  • TLK2711EVM-CVAL: EVM board have pull-up, while device has internal pull-down at PRBSEN.

    TI Thinks Resolved
    Part Number: TLK2711EVM-CVAL Tool/software: Hello. EVM board has pull-up, while device has internal pull-down at PRBSEN. If EVM board Jumper does not installed, PRBSEN voltage is 1.7V. ( 2.5 V * 10k / (4.7k + 10k) ) Intermediate voltage is not…

  • BQ24773EVM-540: EVM has net ties shorting most of GND and PGND on Mid Layer 1?

    TI Thinks Resolved
    Part Number: BQ24773EVM-540 Other Parts Discussed in Thread: BQ24773 Tool/software: I found the EVM design files. I see that there is good separation of GND and PGND on most layers but on MidLayer1 there are long, thin Net-ties that almost entirely bypass…

  • AUDIO-AM275-EVM: Error -1351 - (0:0:0)) Register or Memory request has timed out. The CPU is executing a High Priority Interrupt (typically due to a Double Page Fault

    TI Thinks Resolved
    Part Number: AUDIO-AM275-EVM Tool/software: Env Board: AM275x EVM; Probe: XDS110 IDE: CCS Theia 20.3.0.14__1.9.0 Emulation package (from error): 20.3.0.3656 Project: hello_world_am275x-evm_c75ss0-0_freertos_ti-c7000 (stock) Repro Run…
    • Answered

  • AM6442: Has mcan_loopback_dma been validated on EVM?

    Resolved
    Part Number: AM6442 Hello Champs, SW: mcu_plus_sdk_am64x_09_00_00_35 HW: am64x-evm Customer can't run C:\ti\mcu_plus_sdk_am64x_09_00_00_35\examples\drivers\mcan\mcan_loopback_dma the example without any modfication. Is the mcan_loopback_dma example validated…
    • Resolved
    • Answered

  • DRV8353RS-EVM: Program has compiled correctly, but the BLDC is still not moving

    Resolved
    Part Number: DRV8353RS-EVM Currently with the EVAL firmware pulled from the EVM's site, everything has compiled correctly. The only issue is when using the DRV8353Rx GUI, there seems to be no action happening. Following the DRV8353Rx-EVMInstaSPIN SoftwareQuickStartGuide…
    • Resolved

  • DRV8353RS-EVM: Our motor has been able to run, but the FAULT LED becomes active once the driver gathers torque and starts moving

    Part Number: DRV8353RS-EVM Tool/software: Hi, When we get the motor spinning, we are able to accelerate fine, but the FAULT LED is now lit up. Reading the registers during spinning results in none of Fault Status & VGS Status 2 registers having a flag…

  • MMWCAS-RF-EVM: After calibration, the signal has spurious peaks

    Part Number: MMWCAS-RF-EVM Hi team, Here's an issue from the customer may need your help: 1) A 2-m roof was measured as a calibration matrix, and this echo data was processed using cascade_MIMO_antinnaCalib.m after calibration, using cascade_MIMO_signalProcessing…

  • TUSB320EVM: TUSB320 EVM with 3A output in DFP mode....

    Part Number: TUSB320EVM Other Parts Discussed in Thread: TUSB320 Dear Sir, May I know, if TUSB320 EVM can work in DFP mode with 5V adaptor attached then output 3A from typeC port? My customer did some testing with EVM but still fail to get 3A from…

Didn't find what you are looking for? Post a new question.