Answered

• TXS0206A: How to use CLK-f pin functionality

  

  JD

  Resolved

  Part Number: TXS0206A Dear TI Community, I'm planning to use the TXS0206A in my new design, in between an MCU and an eMMC. The datasheet specifies the CLK-f pin as an output, but I couldn't find much information on how to utilize it to improve the…

  • Resolved

  • 9 months ago
  • Logic
  • Logic forum

• TXS0206A: Can the TXS0206A be used for the SDIO bus voltage conversion?

  

  Jacky Kuo

  TI Thinks Resolved

  Part Number: TXS0206A Dear TI support Team, I would like to use the TXS0206A for my SDIO circuit, designed for voltage conversion between 1.8V and 3.3V for Wi-Fi applications. Is this possible? If yes, what do I need to look for in terms of design? Additionally…

  • over 1 year ago
  • Logic
  • Logic forum

• TXS0206A: The design requirement of clk.f

  

  qiang hao

  TI Thinks Resolved

  Part Number: TXS0206A Hi, Do we have more info introduction about CLK-f? or some reference schematic? Because I saw other vendor's datasheet, they suggest add 25-100mm PCB trace delay to clk-f...I am not sure whether we should do the same thing in TXS0206A…

  • over 1 year ago
  • Logic
  • Logic forum

• TXS0206A: Replacement for the TXS0206A

  

  Conor

  TI Thinks Resolved

  Part Number: TXS0206A Other Parts Discussed in Thread: TXS02612 , , TXS0102 Hi, Can the TXS02612 be used as a replacement for the TXS0206A? From the datasheet it looks like I can use it by fixing the channel. Thanks, Astro

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• TXS0206A: Schematic Review

  

  Allan Fan

  Resolved

  Part Number: TXS0206A Hi expert, Would you please help review customer TXS0206A circuit? There is no requirement e.g. VrefB need to be greater or equal to RefA, correct? Cause the host is higher 3.3V and can't put on B side due to CLKLA must connect to…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• TXS0206A: why voltage translator can be used as redriver

  

  Fred Cheng

  TI Thinks Resolved

  Part Number: TXS0206A Other Parts Discussed in Thread: TWL1200 , TXS0206 Hi team, My customer want a 3.3V ,50MHz SDIO redriver, I see many of you proposing voltage translator like TXS0206 or TWL1200, But aren't those translator and buffer? can they implement…

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• TXS0206A: Overshoot and Undershoot Tolerance

  

  Connor Flack

  Resolved

  Part Number: TXS0206A Can you violate the overshoot and undershoot recommended max voltages if you do not exceed a certain current on this IC? I know this is pretty typical of IC's and the current spec does not allow a lot of wiggle room for overshoot…

  • Resolved

  • over 3 years ago
  • Logic
  • Logic forum

• TXS0206A: Support SD3.0 to compete with IP4856CX25

  

  Jason Shen

  TI Thinks Resolved

  Part Number: TXS0206A Dears My customer have a requirement of SD3.0 interface, and they have found a device of IP4856CX25, which can support. So we are wondering if we have a device can support or not? Jun Shen Thanks

  • over 3 years ago
  • Logic
  • Logic forum
Answered

• TXS0206A: SD card connection on long wires - TXS0206, TXS0108E

  

  Eduardo Garcia68

  Resolved

  Part Number: TXS0206A Other Parts Discussed in Thread: TXS0108E , , SN74AXC4T774 Hello: We have an application in which we need to interface an MCU running at 1.8V to an external board that has an SD Card at 3.3V. We are using SPI to communicate to the…

  • Resolved

  • over 4 years ago
  • Logic
  • Logic forum

• TXS0206A: EN pin left floating

  

  Renan Santos Adriano

  TI Thinks Resolved

  Part Number: TXS0206A Hello Team, Can you confirm what will be the effect if we let the EN pin of TXS0206A floating? Regards, Renan

  • over 4 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.