Search tips
Showing 72 results View by: Thread Post Sort by

  • TXU0304: vs TXU0101 - Quiescent current

    TI Thinks Resolved
    Part Number: TXU0304 Other Parts Discussed in Thread: TXU0101 Hello, Looking at the datasheets of the TXU0304 and the TXU0101 the quiescent current of both devices are identical, is that correct? Nick

  • TXU0101: Need IBIS model

    TI Thinks Resolved
    Part Number: TXU0101 Other Parts Discussed in Thread: TXU0104 , TXU0202 , TXU0102 , TXU0204 , TXU0304 I can't find an IBIS model for this part? Is there an IBIS model for this part? Is it the same with TXU0104? Thank you
    • Answered

  • TXU0101: What is a pull-down resistor of OE pin and Input A pin?

    Resolved
    Part Number: TXU0101 Hi, TXU0101 support team I want to use under the following condition. VCCA=1.8V and VCCB=3.3V Rising time of output signal < 50mV/ns Uni-direction Here are some questions; There are a pull-down resistor on OE pin…
    • Resolved
    • Answered

  • TXU0101: Behavior when the VCC disconnected compared with the LXC counterparts

    Resolved
    Part Number: TXU0101 Hi, I found the LXC parts says: If either VCC supply is < 100 mV or disconnected, all I/O's get pulled-down and then become high-impedance But TXU says: If either VCC input is < ​100 mV or disconnected, all outputs are…
    • Resolved
    • Answered

  • TXU0101-Q1: The output signal is distorted when the frequency of the input signal is ~50MHz

    Resolved
    Part Number: TXU0101-Q1 Other Parts Discussed in Thread: SN74AXC4T774 , SN74AUC1G17 , SN74AUC1G125-EP , SN74AXC8T245 Hello TI Experts, I am using TXU0101-Q1 to translate a 3.3V single-end signals to 1.8V, below is the schematic for your reference. …
    • Resolved
    • Answered

  • PCA9306: EN Control

    Resolved
    Part Number: PCA9306 Other Parts Discussed in Thread: TXU0101 Hi team, I am considering a circuit that controls the EN signal after the VREF1 and VREF2 power supplies are turned on. Can the EN signal be either push-pull or open-drain? I am considering…
    • Resolved

  • TXB0106: Adding series resistance to the TXB0106RGYR

    TI Thinks Resolved
    Part Number: TXB0106 Other Parts Discussed in Thread: TXU0204 , TXU0101 Hello, We have an application where we are running RS232 and RS485 signals through the TXB0106RGYR to level shift between 2.5V and 3.3V. It is unidirectional, but the bidirectional…
    • Answered

  • TAS6424E-Q1: Level translator recommendation for MCLK

    Resolved
    Part Number: TAS6424E-Q1 Other Parts Discussed in Thread: TXU0101 , Tool/software: Hi TI team, We are planning to use the Level tanslator( TXU0101 ) between the processor and Speaker PA (TAS6424E-Q1) to translate the logic level of the signal. Please…
    • Resolved

  • TXS0101: Request for PSpice Model of Voltage Level Translator (1.8V to 5V)

    TI Thinks Resolved
    Part Number: TXS0101 Other Parts Discussed in Thread: TXU0101 Tool/software: Hello TI Community, I am looking for a voltage level translator that can support 1.8V on one side and 5V on the other side. Specifically, I need a PSpice model for simulation…

  • ADS1675: Strange SPI data (samples shifted by one bit)

    Part Number: ADS1675 Other Parts Discussed in Thread: TXU0101 Tool/software: Hi we have a custom board with the ADS1675 and we observe a strange issue: Sometimes two samples samples in the data stream is shifted. One sample is shifted left and the following…

Didn't find what you are looking for? Post a new question.