Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM64x/ AM243x (ALV) / AM62Ax / AM62D-Q1 / AM62Px Design Recommendations / Commonly Observed Errors during Custom board - GPMC memory interface

    Part Number: AM6442 Other Parts Discussed in Thread: TMDS64EVM , , AM5728 , AM67 , PROCESSOR-SDK-AM62X , SYSCONFIG Hi TI Experts, Is there a list of design recommendations or guidelines or E2E references that can be following while implementing GPMC…

  • [FAQ] J721S2XSOMXEVM: How to update KEYREV using TIFS API on HS-SE device?

    Part Number: J721S2XSOMXEVM How can we update KEYREV using the TISCI_MSG_WRITE_KEYREV API on HS-SE device?

  • [FAQ] J721S2XSOMXEVM: EMMC Boot Partition Switching in keywriter application

    Part Number: J721S2XSOMXEVM eMMC has two boot partition 0 and 1 . Boot ROM selects the active partion based on PARTCONFIG register (EXCSD[179]) . How to switch between these in keywriter application?

  • [FAQ] J784S4XEVM: Performance Benchmarking of a Custom Vision Apps Kernel Using GTC Timer and TSC Across Various Optimization Levels

    Part Number: J784S4XEVM Hi Team, How can the performance of a custom kernel be benchmarked using GTC Timer and TSC, and how can the results be evaluated across different optimization levels?

  • [FAQ] AM625: UART Uniflash Flashing Speed Optimization

    Part Number: AM62xx Other Parts Discussed in Thread: UNIFLASH , SYSCONFIG How can flashing speed be improved in UART Uniflash using a higher baud rate? Overview Flashing speed using UART Uniflash on the AM62XX platform can be partially improved. A…

  • [FAQ] AM625: Build DFU enabled U-boot with Yocto for AM62 devices

    Part Number: AM625 Other Parts Discussed in Thread: AM62P , AM62L Overview This article describes how to build and boot DFU enabled U-boot images on TI-K3 devices such as AM62X, AM62A AM62P, AM62L and AM64L using Yocto USB-DFU (Device Firmware Upgrade…

  • [FAQ] AM64x/243x: How to Use Keyring for Authentication of Application Images in MCU+ SDK

    Part Number: AM2434 On HSSE devices, the SYSFW supports the Keyring feature which extends the Root of Trust ( RoT ) to auxiliary keys. This enables the authentication of the application images using these auxiliary keys apart from the programmed SMPKH…

  • [FAQ] AM6XX:How to Port SBL UART UNIFLASH for a custom board

    Part Number: AM62x Other Parts Discussed in Thread: UNIFLASH , AM62P The UART UNIFLASH tool provided in the MCU+SDK will only work for TI EVMs out of the box as it is configured according to Flash and DDR part used in a particular EVM, this FAQ provides…

  • [FAQ] How to boot from dual boot media (OSPI NOR + eMMC) using MCU+SDK?

    Part Number: AM62P Other Parts Discussed in Thread: UNIFLASH Default MCU+SDK SBL examples only support booting from a single boot media (SBL OSPI/SBL EMMC), this FAQ demonstrates how to modify the SBL example to support booting from different boot medias…

  • [FAQ] TDA4VL-Q1: Steps to Build and Run PDK FreeRTOS Example Applications

    Part Number: TDA4VL-Q1 Hello Team, I am looking for guidance on how to build and run the PDK FreeRTOS example applications . Specifically, I would appreciate clarification on the following points: The correct steps to build the PDK FreeRTOS…

View FAQ threads
  • Threads 202732 Discussions