• Threads 52522 Discussions
Texas Instruments (TI) Microcontrollers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search for content on other microcontrollers or ask technical support questions on the extensive portfolio of microcontrollers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] RM48L952: How to perform 8 Byte transfer in SCI Multi-buffered Mode using DMA

    Part Number: RM48L952 When i was writing multi-buffered SCI using DMA in SCI2 Driver. However, my code was able to transmit up to 4 bytes, but when I tried to transmit 8 bytes, the RM48L952 stopped working. Even if I check the datasheet, it seems that…

  • [FAQ] MCU-PLUS-SDK-AM243X: How to use Tune PHY with MCU_PLUS_SDK for OSPI Controller ?

    Part Number: MCU-PLUS-SDK-AM243X Q1. How to tune PHY with MCU_PLUS_SDK ? Q2. Why is PHY tuning required ?

  • [FAQ] AM2634: How to configure Watchdog (WDG) in MCAL?

    Part Number: AM2634 I am currently using MCAL version X.Y.Z how do I configure the WatchDog peripheral to a desired expiry time i.e., After time " t ", the WDG must expire and issue a POR reset if not serviced.

  • [FAQ] MCU-PLUS-SDK-AM263X: How to implement streaming or scatter gather mode for DTHE-AES ?

    Part Number: MCU-PLUS-SDK-AM263X Q1. How to optimize the DTHE-AES engine usage to support multiple algorithm in parallel or support to use it by-parts ? Q2. How to optimize the memory usage by reusing the same region for authentication ? Q3. What…

  • [FAQ] MCU-PLUS-SDK-AM263X: [FAQ] Can you provide the list of FAQs for AM26x devices ?

    Part Number: MCU-PLUS-SDK-AM263X Provide the list of FAQs for AM26x devices segregated domain-wise ?

  • [FAQ] MSPM0L1106: Method to generate Active Low Complementary PWM from single timer-G (TIMG0)

    Part Number: MSPM0L1106 Other Parts Discussed in Thread: MSPM0L1306 , SYSCONFIG The Dead Band feature for PWM generation is only supported in the TIMAx instances of timers and not supported in TIMGx instances available in MSPM0 devices. The following…

  • [FAQ] Sitara AM263x/AM273x MCAL - Getting Started Guide

    Part Number: AM2634 Other Parts Discussed in Thread: UNIFLASH This FAQ aims to address the following Questions: How should MCAL package, FMEDA and other Safety related documents be requested for Sitara MCU+ devices (AM263x, AM273x)? What is the…

  • [FAQ] MCU-PLUS-SDK-AM243X: [FAQ] How to debug/develop/migrate the flash driver for custom flash on non-TI EVM (OSPI/xSPI) ?

    Part Number: MCU-PLUS-SDK-AM243X Other Parts Discussed in Thread: UNIFLASH I am facing issues while migrating the flash driver for custom flash. The flash does not work out of the box with the steps mentioned. How to debug the issues and I am new…

  • [FAQ] MCU-PLUS-SDK-AM243X: [FAQ] How to Configure and Optimize MbedTLS in MCU_PLUS_SDK for am2x devices.

    Part Number: MCU-PLUS-SDK-AM243X Other Parts Discussed in Thread: SHA-256 How to configure MbedTLS features? How to reduce memory footprint of MbedTLS library? How to offload cryptography to custom implementations or crypto engines?

  • [FAQ] MCU-PLUS-SDK-AM263X: [FAQ] How to flash the application via JTAG or SBL JTAG UNIFLASH ?

    Part Number: MCU-PLUS-SDK-AM263X Other Parts Discussed in Thread: UNIFLASH My SBL JTAG UNIFLASH not working.. I am not able to understand how to make SBL JTAG uniflash to work. Can I get some tips to make SBL_JATG_UNIFLASH work ?

View FAQ threads