DRV8343S-Q1EVM: Error File Loader: Verification failed: Values at address 0x04498 do not match Please verify target

Bhuvaneshwaran M

Part Number: DRV8343S-Q1EVM
Other Parts Discussed in Thread: MSP430F5529, MSP-EXP430FR5969, MSP-EXP430FR5739,

I have trying to flash the source code to DRV8343EVB through MSP4305529 launch pad (programmer)kit but I could not flash the code during this I have faced the below issue,

after debug flash setting also got same error .

MSP430: File Loader: Verification failed: Values at address 0x04498 do not match Please verify target memory and memory map.

MSP430: GEL: File: D:\TI_GUI_Work_Space\DRV8343_MSP430F5529_Trapezoidal_Sensorless_BLDC\Debug\DRV8343_MSP430F5529_Trapezoidal_Sensorless_BLDC.out: a data verification error occurred, file load failed.

over 2 years ago

0 Aaron Barrera over 2 years ago

TI__Mastermind 26046 points

Hi Bhuvaneshwaran,

You'll need a MSP-EXP430FR5969 (available on samples.ti.com) or MSP-EXP430FR5739 (available on the TI Store) to flash the MCU on the launchpad via the 4 Spi-by-wire pins on the left side of the DRV8343S-Q1EVM.

Please follow this test procedure: e2e.ti.com/.../faq-drv8343s-q1evm-how-to-flash-firmware-onto-the-drv8343x-q1evm

Thanks,
Aaron

0 Aaron Barrera over 2 years ago in reply to Aaron Barrera

TI__Mastermind 26046 points

Hi Bhuvaneshwaran,

I deleted the replies on the E2E FAQ you replied too, this thread was supposed to be locked. Your replies were below:

Are you following the procedure using Spi-by-wire to flash the code onto the onboard MSP430F5529? You can use any eZ-FET from a Laucnchpad (i.e.MSP-EXP430F5529) to connect the SPI-by-wire pins (3V3, GND, SBWTDIO, SBWTCK) to the 4-pin, 50 mil header on the left side of the DRV8343S-Q1EVM.

Do not change the linker file.

Thanks,
Aaron

0 Bhuvaneshwaran M over 2 years ago in reply to Aaron Barrera

Prodigy 190 points

I have done below make file change of FLASH2 memory ,then I can flash successfully ,

MEMORY
{
SFR : origin = 0x0000, length = 0x0010
PERIPHERALS_8BIT : origin = 0x0010, length = 0x00F0
PERIPHERALS_16BIT : origin = 0x0100, length = 0x0100
RAM : origin = 0x2400, length = 0x2000
USBRAM : origin = 0x1C00, length = 0x0800
INFOA : origin = 0x1980, length = 0x0080
INFOB : origin = 0x1900, length = 0x0080
INFOC : origin = 0x1880, length = 0x0080
INFOD : origin = 0x1800, length = 0x0080
FLASH : origin = 0x4400, length = 0xBB80
//FLASH2 : origin = 0x10000,length = 0x14400
FLASH2 : origin = 0x10000,length = 0x143F8 /* Boundaries changed to fix CPU47 *
INT00 : origin = 0xFF80, length = 0x0002

Thank you

M.Bhuvanesh.

0 Andrew Liu over 2 years ago in reply to Bhuvaneshwaran M

TI__Mastermind 18916 points

Hi Bhuvaneshwaran,

Thanks for your response -

just to confirm - are you saying that the problem is now resolved?

Best Regards,
Andrew

0 Bhuvaneshwaran M over 2 years ago in reply to Andrew Liu

Prodigy 190 points

Yes , that problem resolved

Thanks

M.Bhuvanesh

0 Andrew Liu over 2 years ago in reply to Bhuvaneshwaran M

TI__Mastermind 18916 points

Thanks very much!

Closing this thread, now that a resolution has been found

Best Regards,
Andrew

Motor drivers

Motor drivers forum

DRV8343S-Q1EVM: Error File Loader: Verification failed: Values at address 0x04498 do not match Please verify target