TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel
Motor drivers

Motor drivers

Motor drivers forum

  • Mentions
  • Tags
  • More
  • Cancel
  • Ask a new question
  • Ask a new question
  • Cancel
Texas Instruments (TI) Motor drivers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search motor drivers IC content or ask technical support questions on everything from brushless DC (BLDC) and brushed DC (BDC) motor drivers to stepper motor and other drivers for precise motor control. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions
  • [FAQ] Selecting the Best IDRIVE setting and Why this is Essential

    Adam Sidelsky
    Adam Sidelsky
    Using the wrong IDRIVE setting can damage your FET or DRV as it often causes excessive ringing and/or cross-conduction when the Gates are slammed on or off too strongly. This document discusses the methods and some Do's and Don'ts IDRIVE Do's and Don…
    • over 6 years ago
    • Motor drivers
    • Motor drivers forum
  • [FAQ] Best Practices for PCB layout of Motor Drives

    James Lockridge19
    James Lockridge19
    "What are good layout practices for your motor driver IC?" This is a question frequently asked to TI's motor driver team. Poor layout can result in poor EMI performance, poor thermal performance, or sometimes the motor driver device just doesn't work…
    • over 6 years ago
    • Motor drivers
    • Motor drivers forum
<

View FAQ threads
  • Tags
  • RSS
  • More
  • Cancel
  • Answered

    MCT8329A: To wirte parameters from the MCU external to the MCT8329A via I2C. 0 Locked

    323 views
    4 replies
    Latest over 2 years ago
    by Hong Khor
  • Not Answered

    DRV8706-Q1: Doubler(DRV8706) or Tripler(DRV8718) Charge Pump 0 Locked

    403 views
    3 replies
    Latest over 2 years ago
    by Jacob Thompson
  • Answered

    DRV10987: DRV10987 Pspice model 0 Locked

    296 views
    2 replies
    Latest over 2 years ago
    by Ceyhun Ozmutlu
  • Suggested Answer

    DRV8305-Q1EVM: F320F28027 0 Locked

    193 views
    2 replies
    Latest over 2 years ago
    by Joshua Maize
  • Answered

    DRV8705-Q1: How to implement Offline Short Circuit and Open Load Detection on independant PWM mode? 0 Locked

    344 views
    4 replies
    Latest over 2 years ago
    by Shinya Morita
  • Not Answered

    DRV10987: Motor wont start and gives Stuck in open loop fault 0 Locked

    1693 views
    49 replies
    Latest over 2 years ago
    by Vishnu Balaraj
  • Suggested Answer

    DRV10987: speed issue 0 Locked

    183 views
    1 reply
    Latest over 2 years ago
    by Vishnu Balaraj
  • Suggested Answer

    DRV8329: Power Rating for Bootstrap Diodes 0 Locked

    281 views
    2 replies
    Latest over 2 years ago
    by Akshay Rajeev Menon
  • Suggested Answer

    DRV8703-Q1: How Does Doubler Charge Pump work, why is this better than using bootstrap capacitor, is there any restriction on using charge pump 0 Locked

    3107 views
    12 replies
    Latest over 2 years ago
    by David Larkin
  • Not Answered

    DRV8462: TRQ_DAC Overdriven when ATQ_EN=1 0 Locked

    217 views
    2 replies
    Latest over 2 years ago
    by Jacob Thompson
  • Suggested Answer

    DRV8711: What should we do on STEP and DIR pins when pure SPI control? 0 Locked

    249 views
    1 reply
    Latest over 2 years ago
    by Jacob Thompson
  • Suggested Answer

    DRV8434S: What should we do on STEP and DIR pins when pure SPI control? 0 Locked

    405 views
    1 reply
    Latest over 2 years ago
    by Ryan Kehr
  • Answered

    DRV8705S-Q1EVM: Can DRV8705 (or DRV870x) drive an H-bridge that is for 100A? 0 Locked

    387 views
    3 replies
    Latest over 2 years ago
    by Ryan Kehr
  • Answered

    DRV8353F: DRV835xF use as full bridge 0 Locked

    250 views
    1 reply
    Latest over 2 years ago
    by Joshua Maize
  • Not Answered

    MCF8316AEVM: Device and Pin configuration is missing a selection toggle switch 0 Locked

    103 views
    0 replies
    Started over 2 years ago
    by Stavros Danos
  • Not Answered

    DRV8231A: Need help debugging DRV8231A Circuit 0 Locked

    419 views
    1 reply
    Latest over 2 years ago
    by David Medis
  • Not Answered

    DRV8243S-Q1LEVM: Problems with chip debugging 0 Locked

    231 views
    1 reply
    Latest over 2 years ago
    by Ryan Kehr
  • Suggested Answer

    DRV8245-Q1: Hi-Z state 0 Locked

    248 views
    3 replies
    Latest over 2 years ago
    by Ryan Kehr
  • Suggested Answer

    DRV8306 크랙: The current value is high and the motor is hot. 0 Locked

    563 views
    11 replies
    Latest over 2 years ago
    by Hong Khor
  • Suggested Answer

    DRV8210: Is there any limitation for VM VCC sequence 0 Locked

    301 views
    1 reply
    Latest over 2 years ago
    by David Medis
<>