Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM62A7: Bad Block Implementation for NAND Flash Parts

    Part Number: AM62A7 Other Parts Discussed in Thread: SYSCONFIG Tool/software: From release 10.00.00.14 onwards, BBM has been implemented in TI Drivers for NAND Flash Parts. AM62A MCU SDK: https://www.ti.com/tool/download/MCU-PLUS-SDK-AM62A/10.00…

  • [FAQ] TPS62867: TPS62867RQYR head room

    Part Number: TPS62867 Tool/software: Hi Experts, Customer is using the below device The input is 3.6V - 5% The output is 3.3V + 5% Current 1-2 A. Is there a min voltage difference that is required between the output and the input. Regards…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62Ax / AM62D-Q1 / AM62Px / AM62L / AM64x / AM243x Design Recommendations / Custom board hardware design – SOC ROC Recommended Operating Condition

    Part Number: AM625 Tool/software: HI TI experts, I have a question on the SOC ROC. Can i consider the ROC to be ±5% of the Nominal value for the supply rails or should i be considering the values mentioned in the data sheet ( some of the supplies…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM62Ax / AM62D-Q1 / AM62Px / AM64x / AM243x Design Recommendations / Custom board hardware design – Queries related to CAP_VDDSx CAP_VDDS

    Part Number: AM625 Other Parts Discussed in Thread: AM62D-Q1 , AM62L Tool/software: HI TI experts, Could you provide recommendations on CAP_VDDSx, cap value and effect of the capacitor not mounted or shorted.

  • [FAQ] PROCESSOR-SDK-AM57X: U-boot patch for Linux addressing AM57xx errata i2446

    Part Number: PROCESSOR-SDK-AM57X Tool/software: This is a patch to made for U-boot as an example of how to implement the workaround for AM57xx errata i2446:

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP: Ethernet PHY RGMII synchronous clock

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62B-P1 Tool/software: Hello, May I have question about SoC clock? Q1 In this document, https://www.ti.com/lit/an/sprad21e/sprad21e.pdf It says EPHY need match clock to SoC. Is the…

  • [FAQ] SK-AM64B: Why the Ethernet phy use the same clock buffer?

    Part Number: SK-AM64B Tool/software: Hi Team, I found in the schematic of EVM, we only use one piece of LMK1C1103PWR to buffer clock signal to 2 pieces of Ethernet PHY. Does it necessary to use one clock buffer? Can the different Ethernet PHY use…

  • [FAQ] AM6442: AM6442 MMC1

    Part Number: AM6442 Tool/software: Hi Team, We are using AM6442 for our new design. We are connected eMMC to MMC0 and we want to connect wifi module's SDIO signals to MMC1. Wifi module SDIO signal voltage level is 1.8v. We just want to confirm what…

  • [FAQ] AM6442: Watchdog debug and configuration guide for all SITARA AM6X MPU devices

    Part Number: AM6442 Tool/software: This FAQ provides a comprehensive guide to configuring and debugging the watchdog timer with a focus on all SITARA MPU devices in different real time use cases . The guide addresses key concepts such as whether…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM64x / AM243x / AM62Ax / AM62Px / AM62D-Q1 / AM62L - Bootmode implementation with isolation buffers used

    Part Number: AM625 Other Parts Discussed in Thread: AM62L , AM62P Tool/software: Hi TI Experts, Do you have any suggestion on configuring the bootmode pins for alternate functions? I am using the bootmode resistors + buffers to configure the SOC…

View FAQ threads
  • Threads 198461 Discussions