Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM62A / AM62P / AM62D-Q1 / AM64x / AM243x Design Recommendations / Custom board hardware design - List of errors observed during customer schematics review

    Part Number: AM625 Tool/software: Hi TI experts, is there a list of common errors observed when reviewing customer schematics

  • [FAQ] EDGE-AI-STUDIO: Is SDK version important for Edge AI and TI Deep learning (TIDL) with C7x on AM6xA SoCs [AM62A, AM67A, AM68A, AM68PA, AM69A]?

    Part Number: EDGE-AI-STUDIO Other Parts Discussed in Thread: AM68A , AM67A , SK-AM62A-LP Tool/software: We receive frequent queries related to SDK versions and TI Deep Learning (TIDL). Please find a series of relevant FAQ topic below. Note that these…

  • [FAQ] TDA4VM: How to adjust ALE classifier/policer partition in ETHFW

    Part Number: TDA4VM Other Parts Discussed in Thread: TDA4VH Tool/software: The number of user configurable ALE classifier/policer entries are limited in ETHFW by dividing them in to multiple partitions, how to adjust those partitions?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM62A / AM62P / AM62D-Q1 / AM64x / AM243x Design Recommendations / Custom board hardware design - Queries related to SOC data sheet Pin Attributes Excel format

    Part Number: AM6442 Other Parts Discussed in Thread: AM625SIP , AM62P , AM62L Tool/software: Hi TI Experts, Can you supply the pin list of the SOC in excel format?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62Ax / AM62Px / AM62D-Q1 / AM62L / AM64x / AM243x Design Recommendations / Custom board hardware design - Drive Strength Configuration for SDIO and LVCMOS I/Os

    Part Number: AM625 Other Parts Discussed in Thread: AM62A7 , Tool/software: Hi TI Experts, I have the below query AM62A7: How can we change the drive strength of the SPI interface AM625: How to change the drive strength of the ethernet interface…

  • [FAQ] TDA4VL-Q1: ECC Testing Procedure for Inaccessible RAM IDs

    Part Number: TDA4VL-Q1 Tool/software: Does the SDL ECC test cover error injection tests on the inaccessible endpoints? If not, what is the testing procedure for these endpoints?

  • [FAQ] TDA4VH-Q1: ECC Testing Procedure for Inaccessible RAM IDs

    Part Number: TDA4VH-Q1 Tool/software: Does the SDL ECC test cover error injection tests on the inaccessible endpoints? If not, what is the testing procedure for these endpoints?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP: MCU_PORz input slew rate

    Part Number: AM623 Other Parts Discussed in Thread: AM625 Tool/software: Usually add RC filter on RESET signal to anti noise, but the slew rate requirement of RESET signal on AM62x datasheet is quite sharp, on customer board it is about 10V-100V/ms…

  • [FAQ] AM623: MMC0 HS200 slew rate

    Part Number: AM623 Tool/software: #1. Did not find MMC0 HS200 slew rate data in datasheet timing section, so section 7.8.6 LVCMOS Electrical Characteristics data applies? #2. The Min vale: 18f or 1.8E+6, the two value are quite different, 18f=18x200MHz…

  • [FAQ] Guideline on the Initial Software Post on E2E

    When posting a new software inquiry on the TI E2E forum, please follow this guideline for the initial post. Describing the Problem Using the following list of questions as the template, copy and paste the questions to your post, and answer them if…

View FAQ threads
  • Threads 198419 Discussions