Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM625: MCSPI MISO MOSI IDENTIFICATION

    Part Number: AM625 Tool/software: Hi Ti Experts, I am designing a custom board for the AM6254 SoC and trying to connect an SPI peripheral to the AM6254 SPI interface. I intend to use MCU_SPI1 Channel but I am not sure which one is MISO and MOSI…

  • [FAQ] TDA4AP-Q1: How to Set PCIe0 Transmitter De-emphasis

    Part Number: TDA4AP-Q1 Tool/software: Hi TI Experts, Customer is working on TDA4AP SDK10.0. They are using SPL boot. They want to change the De-emphasis to be -3.5dB for PCIe0 for 5.0GT/s to minimize reflection. Please see the below description…

  • [FAQ] AM62X/AM62Ax/AM62Px: What to do if Linux fails to initialize remoteproc with DM R5F?

    I am using a processor with a DM R5F (AM62x, AM62Ax, AM62Px). I am using SDK 9.2.1 or SDK 10.0. The Device Manager (RM) R5F core is listed in the Linux devicetree, so Linux should use the remoteproc driver to attach to the DM R5F during Linux boot time…

  • [FAQ] SK-AM69: How to stream from CSI sensor and USB camera to display using GStreamer?

    Part Number: SK-AM69 Other Parts Discussed in Thread: SK-AM68 , AM67 , SK-TDA4VM Tool/software: Hi, I have a Starter Kit (SK) Edge AI device with a CSI sensor connected and would like to stream to my display. I have enabled the sensor by following…

  • [FAQ] : How to test ECC for R5F Cache Memories on AM6x/AM243 devices.

    Part Number: SK-AM62B-P1 Tool/software: Is ECC (SEC/DED) testing possible on R5F internal cache memories? If yes, please provide the steps to do so.

  • [FAQ] AM625: Package parameter description

    Part Number: AM625 Other Parts Discussed in Thread: AM623 Tool/software: Hi TI, I`d like to know the meaning of below parameter. 0.35, 0.25, 0.15, 0.08. What is the meaning of these 4 parameter? BR Cayden

  • [FAQ] AM2432: Please give some information of Schematic design for FSI?

    Part Number: AM2432 Other Parts Discussed in Thread: AM6412 , AM6422 , AM6442 , AM2434 Tool/software: Hi At the document SPRACU5C "AM6442, AM6422, AM6412 and AM2434 Schematic Design and Review Checklist" ( link ), there is no description for FSI…

  • [FAQ] AM62A3-Q1: AM62A3-Q1 PDN Power SI SIMULATION Questions

    Part Number: AM62A3-Q1 Tool/software: Hello，I have some doubts about PDN simulation (Power SI), please help to solve it 1、Do I need to separate VDD_CORE-1 to 17 for simulation, or use VDD_CORE as a Port? 2、Do I need to include the PMIC FB loop…

  • [FAQ] How to Setup IBV icECAT EtherCAT Master Stack on TI Processors?

    Part Number: AM6442 Other Parts Discussed in Thread: LP-AM243 , TMDS64EVM Tool/software: icECAT is a 3rd party EtherCAT Master stack developed by IBV . To obtain the software stack for evaluation please send a request by selecting the "Send Request…

  • [FAQ] How to Setup an EtherCAT Network using TI Processors

    Part Number: AM6442 Tool/software: TI processors have the capability to run as an EtherCAT MainDevice to control EtherCAT SubDevices such Beckhoff I/O terminals or an AM243x running an EtherCAT subdevice example . This is enabled by using a 3rd…

View FAQ threads
  • Threads 197825 Discussions