Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] SK-TDA4VM: How to create Object Classification Reference Design using Edge Impulse platform on TDA4VM-SK

    Part Number: SK-TDA4VM Other Parts Discussed in Thread: TDA4VM Edge Impulse is a tool for creating, analyzing, and deploying machine learning to embedded targets. TI Processors, like the TDA4VM and AM62x, running the default Processor SDK for Linux…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP / AM62A7 / AM62A3 / AM62A1-Q1 / AM62D-Q1 / AM62P / AM62P-Q1 / AM62L Custom board hardware design – Queries regarding Crystal selection and clock specifications

    Other Parts Discussed in Thread: SK-AM62 , SK-AM62-LP , AM62P , AM62D-Q1 , AM62A3 , AM62A7-Q1 , AM62A3-Q1 , AM62A7 , AM62P-Q1 , AM62L , AM620-Q1 , AM625 , AM623 , AM625-Q1 , AM625SIP , AM6442 , AM3352 , OMAP-L138 Hi TI Experts, I have the below queries…

  • [FAQ] AM625: Adding SD card (mmc1) support to skeleton DTS

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62 Hello, I'm using tisdk-base-image and k3-am625-skeleton.dts on SK-AM62 as a starting point. I modified k3-am625-skeleton.dts to enable mmc0 & mmc1, but mmc1 does not seem to be recognized…

  • [FAQ] AM6x: Ethercat Master using Linux

    Part Number: PROCESSOR-SDK-AM64X PROCESSOR-SDK-AM62X Hi TI Expert, Question1: Is there any open source code to recommend for EtherCAT MainDevice in Linux ? Answer: There is an constrained open source EtherCAT MainDevice at https://etherlab…

  • [FAQ] TDA4VM: How to flash images to the EMMC Boot 0 partition using tftp?

    Part Number: TDA4VM How can we flash the boot images to the emmc boot 0(raw mode) partition using tftp?

  • [FAQ] AM625/AM623 EVM SK-AM62 - Bootmode configuration

    Other Parts Discussed in Thread: SK-AM62 Hi TI Experts, Could you guide me on configuring the SK-AM62 EVM Bootmode for the below board revisions and testing? 1. Dip Switch Setting for E1 2. Dip switch setting for E2/E3 3. DFU Bootmode does not…

  • [FAQ] TDA4VM: How to boot from the emmc UDA partition in FS mode using SPL boot flow?

    Part Number: TDA4VM How can we boot from the emmc uda partition in the FS boot mode using SPL boot flow ?

  • [FAQ] TDA4VL-Q1: How to configure DDR size of 4GB in the J721s2 SDK?

    Part Number: TDA4VL-Q1 What are the changes required to be done in the Linux SDK support a DDR of size 4GB?

  • [FAQ] TDA4xx: How to load sysFw from ROM in SBL boot flow

    This FAQ shows how to boot tifs.bin from ROM instead of SBL.

  • [FAQ] TDA4VM: How to identify a GPIO and toggle the same

    Part Number: TDA4VM How can we profile a code using GPIO? What are the steps to identify which GPIO to be used and how to toggle the same?

View FAQ threads
  • Threads 197996 Discussions