Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] 66AK2H12: EVMK2H U-Boot build

    Part Number: 66AK2H12 Other Parts Discussed in Thread: 66AK2H06 , 66AK2H14 How to build U-Boot from "Processor-SDK-Linux" for K2H Family devices (EVMK2H, 66AK2H12, 66AK2H06, 66AK2H14 )?

  • [FAQ] TDA4VM: How can I configure the Memory Protection Unit (MPU) for the R5F running FreeRTOS and baremetal case?

    Part Number: TDA4VM Other Parts Discussed in Thread: SYSBIOS I'm aware of the r5_mpu.xs file used to configure the MPU and needed to be included in the sysbios.cfg in case of TI RTOS. How can I do the same in FreeRTOS, is there a similar XDC based configuration…

  • [FAQ] TDA4VM: Configuring stack and heap size in FreeRTOS application

    Part Number: TDA4VM I'm trying to understand how to control the system stack and heap size in a FreeRTOS application. I see defines like below 1) --stack_size & -stack 2) --heap_size & -heap Q1. Which one of these should be used for stack and…

  • [FAQ] TI's EdgeAI @ Embedded World 2022 : Evaluate examples

    Hello, Here is a quick look at live demonstrations on TI's Edge AI Platform shown at Embedded World 2022 . These examples can be easily recreated on TI’s devices, please see the table below for links to relevant Software and Hardware modules. Setup…

  • [FAQ] 66AK2H12: How to flash the SBL ( Secondary Boot loader ) into NOR and how to flash the application binary into NOR? How to boot the SBL + Application binary?

    Part Number: 66AK2H12 Hi, How to flash the SBL ( Secondary Boot loader ) into NOR and how to flash the application binary into NOR? How to boot the SBL + Application binary? on K2H board.

  • [FAQ] AM625: MMC interface

    Part Number: AM625 Hi experts I have some problems about AM6254 mmc part 1. Is it feasible to use the second MMC interface (MMC2) of TI's AM6254x as the boot of the SD card? Because this group of SDCD&SDWP and other data lines are together and can…

  • [FAQ] TDA4VM: How LDC LUT can be converted from text to binary format and be used in SDK?

    Part Number: TDA4VM Hi Gang, I'm doing distortion correction on TDA4 using DCC tool, and I have found your workflow instruction: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1058565/faq-tda4vm-how-to-create-a-ldc-mesh…

  • [FAQ] TDA4VM: J72E : How to determine if this is a GP or HS device

    Part Number: TDA4VM HI, How to determine if this is a GP or HS device，Thank you for your help. Best regards huahui

  • [FAQ] 66AK2E05: Would you please provide a "Quick start Guide for K2E - EVM " to enable a quick product development ?

    Part Number: 66AK2E05 Other Parts Discussed in Thread: SYSBIOS , CCSTUDIO , Hi, Would you please provide a "Quick start Guide for K2E - EVM " to enable a quick product development ?

  • [FAQ] 66AK2H12: UART Example project for K2H family devices

    Part Number: 66AK2H12 Explain the Code, Hardware configuration, and Implementation of the UART example project in K2E family devices?

View FAQ threads
  • Threads 198147 Discussions