Frequent Questions

  • [FAQ] Debugging Low Power Modes on AM62 Family Devices (AM62x/A/D/P/L)

    Part Number: AM625 Other Parts Discussed in Thread: AM62P , AM62L Hello, I am using a low power mode on an AM62 Family device including AM62x, AM62P, AM62A, AM62D and AM62L. What are some steps to debugging why the low power modes is not working as…

  • [FAQ] TAS2120: What are the proper considerations when driving a high-inductance actuator with TI Class-D amplifiers?

    Part Number: TAS2120 When driving high-inductance actuators, the phase shift of current and voltage in the load can cause reverse-current issues triggering Class-D amplifier protection schemes such as over-current and over-voltage. The attached spreadsheet…

  • [FAQ] TDA4VH-Q1: How to use Cross-Domain MDIO Pins of CPSW

    Part Number: TDA4VH-Q1 Other Parts Discussed in Thread: TDA4VH The MDIO pins and the data pins routed to PHY are from different instances of CPSW due to Hawdware constrain or referencing by mistakenly, How to address this issue and possibility for using…

  • [FAQ] TMS320F28P550SJ: Common Issues Related to SysConfig GUI

    Part Number: TMS320F28P550SJ Other Parts Discussed in Thread: SYSCONFIG , C2000WARE Hello, Please check out the debugging steps for some of the common issues users face while using TI's peripheral and device configuration tool - SysConfig. Thanks…

  • [FAQ] AM4372, AM4376, AM4377, AM4378, AM4372, AM4379, AM4382, AM4384, AM4389 Design Recommendations / Custom board hardware design - Getting started and Design Guidelines

    Part Number: AM4372 Other Parts Discussed in Thread: TPS65218 , TPS65218D0 , TPS65910 , TPS65217 , TPS650250 , TPS6521825 , TPS6521815 , TMDXEVM438X-EPOS , TMDSEVM437X , AM5728 , AM4378 Hi TI Experts, I am working on a design using AM437x or AM438x…

  • [FAQ] TDA4x: When bringing up CSI-RX, what order do I need to enable components in?

    Part Number: TDA4VH-Q1 I have a camera, serializer, and deserializer, and I'm trying to capture video on CSI-RX. What order do I need to enable the devices in? What issues may appear if the order is incorrect?

  • [FAQ] TIDA-050026-23881: Dynamic Power Management - Expected Behaviors

    Part Number: TIDA-050026-23881 One of the main challenges of designing a multi-port system is supporting all ports on a full load using a limited power supply. TI’s FirmPSE system-level firmware solution provides designers with various power supply…

  • [FAQ] AM263P4-Q1: How to run FLS SIP examples in AM263P SIP Device?

    Part Number: AM263P4-Q1 Please provide the steps to run FLS SIP examples on AM263P SIP Device

  • [FAQ] TDA4VH-Q1: How to get Traffic profile for c7x core using cp trace

    Part Number: TDA4VH-Q1 Hi Team, Could you guide me on the steps to get the traffic profile for c7x cores using cp trace?

  • [FAQ] TDA4VH-Q1: How to Pass VLAN 0 Packets Transparently Through CPSW Using the Native Linux Driver

    Part Number: TDA4VH-Q1 By default, CPSW does not pass VID 0 (priority-tagged) frames as-is. The Linux driver strips or replaces VID 0 at both ingress and egress, making it impossible for the use-cases that require VID 0 with priority bits set on the…

View FAQ threads
Recommended For You