Answered

• CDCE913-Q1: maximum supply current

  

  Shinji Tsuji

  Resolved

  Part Number: CDCE913-Q1 Hi team, Could you advise the maximum supply current of CDCE913-Q1 for IDD and IDDOUT parameters below? regards,

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCE913: Cannot read register throuh I2C ?

  

  BL

  Resolved

  Part Number: CDCE913 Hi, I have problem at reading out registers of CDCE913 via I2C interface. I have checked the I2C signals in Oscilloscope and it looks correctly to me, however I received a NotAcknowledge at the end of read operation. Could you please…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

• CDCE913-Q1: rise fall time can not meet the datasheet

  

  YY

  TI Thinks Resolved

  Part Number: CDCE913-Q1 Hello Team, I got a question from my customer which is about rise/fall time. The customer can't meet rise/fall time limitation of CLK_IN as below requirement. However, the time was 5.2ns at worst case from customer. The customer…

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

• CDCE913: power on reset

  

  Shinji Tsuji

  TI Thinks Resolved

  Part Number: CDCE913 Hi team, I would like to cycle VDD/VDDout pin when they drops below recommended range to reset internal registers. 1. Could you advise the minimum recommended turn off time and minimum voltage for properly achieve reset? ( for example…

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

• CDCE913: Clock Pro can't be loaded saved file.

  

  YY

  TI Thinks Resolved

  Part Number: CDCE913 Hello Team, I got a question from my customer. The customer tried to load setup file. However, Clock Pro generated error massage. The customer operated as below sequence. 1, run Clock pro and set up frequency (fin: 18.432MHz, fout…

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCE913: M value calculation from ClockPro

  

  shibatani

  Resolved

  Part Number: CDCE913 Other Parts Discussed in Thread: CLOCKPRO Hello Would you please let me know about M value in ClockPro? Q1 If I set fin = 24MHz , and if I choose fout= 24* 1000/1001 =23.97602397MHz, I can calculate from ClockPro as fout = 24 *…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCE913: How to change fout on the fly

  

  shibatani

  Resolved

  Part Number: CDCE913 Other Parts Discussed in Thread: CLOCKPRO Hello Would you please let me know the way how to change the fout on the fly without lost of fout / or unexpected frequency of fout? Q1 How can I change fout(MHz) on the fly by changing N…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

• CDCE913-Q1: SetupCopyOEMInfo() Failed with error 0x5

  

  Koji Hayashi92

  TI Thinks Resolved

  Part Number: CDCE913-Q1 Other Parts Discussed in Thread: CDCEL9XXPROGEVM Hi TI-team I use CDCEL9XXPROGEVM. But The PC( windows 10) does not recognize EVM. https://e2e.ti.com/support/clock-and-timing/f/48/p/960089/3549356?tisearch=e2e-sitesearch&keymatch…

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCE913-Q1: Propagation delay when PLL is used

  

  Yuta Kurimoto

  Resolved

  Part Number: CDCE913-Q1 Hello Team, I got some questions from customer about the CDCE913-Q1. Q. How much propagation delay from VDD(1.8V) ramp up to start output clock? Q. How much propagation delay from VDD(1.8V) ramp down to stop output clock? [Condition…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

• CDCE913-Q1: Datasheet formula

  

  Guenter Fettig

  TI Thinks Resolved

  Part Number: CDCE913-Q1 Please check on correctness of below datasheet statements at page 23: 0≤R≤511 instead of 0≤R≤51 & unit µs seem to be wrong P=4-int(log2 (N/M)) instead of P = 4-int(log2 N/M)

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.