• ISO35T: Vcc2 = 5V

  

  Shachar Armon

  TI Thinks Resolved

  Part Number: ISO35T Other Parts Discussed in Thread: ISO3086T Hello, We intend to use ISO35TDWR with Vcc2=5V I can notice it fine to have Vcc2 up to 6V, but the recomendded is Vcc2=3.6V What is the limitation or impact of the circuit under this…

  • 4 months ago
  • Isolation
  • Isolation forum

• ISO35T: FIT value for ISO35TDWR

  

  Krzysztof Suchocki

  TI Thinks Resolved

  Part Number: ISO35T Tool/software: Hi, I am preparing FMEDA for a project that has ISO35TDWR. Please provide the FIT value, error types and their distribution. Best regards Krzysztof Suchocki

  • over 1 year ago
  • Isolation
  • Isolation forum
Answered

• ISO35T: Recommendations to use ISO3086TDWR as drop-in alternate

  

  Filiberto Perez Maya

  Resolved

  Part Number: ISO35T Other Parts Discussed in Thread: ISO3086T Looking into using ISO3086TDWR to replace ISO35TDWR as a drop-in replacement to cover a shortage in supply. I looked at the comparisons (link below) and we should be ok, but there are differences…

  • Resolved

  • over 2 years ago
  • Isolation
  • Isolation forum
Answered

• ISO35T: ISO35TDW

  

  Dheeraj Jain

  Resolved

  Part Number: ISO35T Other Parts Discussed in Thread: ISO3086T , ISOW1432 , ISO1500 , ISOW1412 , ISO1432 Hi, Our customer is looking ISO35TDW for their end product. This part is out of stock. Is their other equivalent part in SOIC-16 package you can…

  • Resolved

  • over 3 years ago
  • Isolation
  • Isolation forum

• ISO35T: Total current consumption require

  

  S Ch

  TI Thinks Resolved

  Part Number: ISO35T How much accually Total current consumption require to VCC1 (also supply to T1 for VCC2) , 3.6V when design follow SLUU470? from datasheet is specfiy 60 mA, 3.6V, and Typical efficiency 60% , that mean I have to supply 3.6V and…

  • over 4 years ago
  • Isolation
  • Isolation forum

• ISO35T: if rs485 more node, is it consume more current consumption or not?

  

  S Ch

  TI Thinks Resolved

  Part Number: ISO35T I wonder if I use ISO35T to connect rs485 32 node vs 256 node, are they current consumption is it the same, 60mA for driver. from datasheet is specify driver can take up to 60mA consumption.

  • over 4 years ago
  • Isolation
  • Isolation forum
Answered

• RE: ISO35T: ISO35TDW supports profibus or not

  

  FRANK1

  Resolved

  Hi Rao, Thank you. do you know why ISO35T doesn't support Profibus ? Regards,

  • over 5 years ago
  • Isolation
  • Isolation forum
Answered

• ISO35T: Operation when Vcc1 is off and RS-485 side is Active

  

  KAEDE KUDO

  Resolved

  Part Number: ISO35T Other Parts Discussed in Thread: ISO1430 , ISO1410 Hello My customer is using ISO 35T in the following circuit. Primary Side is powered off. RS-485 side is active and 1.2VDC is applied to Y and Z. At this time, 0.5V is observed…

  • Resolved

  • over 6 years ago
  • Isolation
  • Isolation forum
Answered

• RE: ISO35T: Regarding 5V-tolerance

  

  Koteshwar Rao

  Resolved

  Hi Ludvig, Thank you for using E2E Forum. The recommended voltage for VCC of ISO35T is 3.15V to 3.6V and the inputs should also be maintained under VCC for normal operation. 5V tolerant input means that the inputs can withstand 5V if 5V is applied…

  • over 7 years ago
  • Interface
  • Interface forum

• RE: ISO35T: Multiple parts on same board - drawing excess current

  

  Manuel Chavez

  Hi Solarmax, This reply is being posted for completeness to everyone following this thread: Upon following up offline and testing on both Solarmax's end and TI's end, it was determined that the ISO35T devices used in this system were defective out…

  • over 7 years ago
  • Isolation
  • Isolation forum

Didn't find what you are looking for? Post a new question.