Search tips
Showing 2,335 results View by: Thread Post Sort by

  • LM4041-N-Q1: Latch-up current for VDD

    TI Thinks Resolved
    Part Number: LM4041-N-Q1 Tool/software: Hi team, This is FAE Jayden, My customer is using LM4041QCEM3X-1.2NO. They need to evaluate the latch-up current of the device's VDD pin to guide their design. If you cannot provide this data, can you provide an…

  • LM4040-N-Q1: Referencing shunt voltage reference to positive rail

    Part Number: LM4040-N-Q1 Other Parts Discussed in Thread: LM4040-N Tool/software: I'm currently using a zener diode to create a voltage approximately 2.5 to 3 volts below a positive rail, depending on the zener selected. The rail can vary from 11 to 16…

  • DRV2605L-Q1: Do we have recommended LRA vendor or LRA P/N to use along with DRV2605L-Q1?

    TI Thinks Resolved
    Part Number: DRV2605L-Q1 Tool/software: Hi team, It's the 1st time for my customer to design a display which can automatically rotate the content displayed when the screen is rotated. They are evaluating DRV2605L-Q1, but they don't have much idea…

  • LM4040-N-Q1: Operating temp range of 4.096V precision voltage reference

    TI Thinks Resolved
    Part Number: LM4040-N-Q1 Tool/software: what is the operating temperature range for the LM4040A41IDBZR. On Mouser, it states -40 to 125 C, but the datasheet does not match that information. Also the datasheet says there is an extended temp range of …

  • LM4040-N-Q1: Alternative for TPR6040-S

    TI Thinks Resolved
    Part Number: LM4040-N-Q1 Hi Team, Could you pls recommend an completive alternative for TPR6040F30-S3TR-S(accuracy 0.1%)? Regards, Hailiang

  • RE: TCAN4550-Q1: do`n read Device ID

    Hello, I hope somebody answer my querstion. I completed the TCAN4550 initialization refer to the TCAN demo, but when I called the function TCAN4x5x_MCAN_ClearInterruptsAll // Resets all MCAN interrupts (does NOT include any SPIERR interrupts). then I…
    • Answered

  • CDCE6214-Q1: SECREF_P/N pins floating when not used/not connected?

    Resolved
    Part Number: CDCE6214-Q1 Tool/software: Dear Madam or Sir, I am planning to use the CDCE6214-Q1. I do not plan to use the secondary reference clock inputs: SECREF_P/N. Can I leave these pins unconnected and floating, or should I bias/connect them to…
    • Resolved
    • Answered

  • TDA4AP-Q1: Pin Swap for SERDES2_TX2 / RX2 P/N possible via register configuration

    Resolved
    Part Number: TDA4AP-Q1 Tool/software: Hello, is it possible to swap the P/N pins for SERDES2_TX2 / SERDES2_RX2 (pins AR21, AR20 / AU20, AU21) by register setting? We're using this port for SGMII/QSGMII SGMII interface 1. Thanks for your answer in advance…
    • Resolved

  • RE: TAS6584-Q1: THD+N at high temp PBTL

    Hi Tsuji-san What is the condition difference between below two picture? Is it only the temperature difference with 25C and 80C? It seems quite larger than our results. And the low frequency THD also increased a lot, which indicated the noise becomes…

  • LM4050-N-Q1: Component type for SN29500

    TI Thinks Resolved
    Part Number: LM4050-N-Q1 Hi Expert, My customer is doing the FuSa analysis for their system. LM4050 is used in this project. Can you help fill the component type to the excel for LM4050 based on SN29500? I saw there have SN29500 category in FuSa FIT…

Didn't find what you are looking for? Post a new question.