Search tips
Showing 43 results View by: Thread Post Sort by
    Answered

  • OPA356: Ceramic bypass capacitor value

    Resolved
    Part Number: OPA356 Other Parts Discussed in Thread: OPA355 , Hello team, On datasheet, it recommends to use 10uF ceramic bypass cap. is this a typo? Isn't it supposed to be 10nF? Best Regards, Kei Kuwahara
    • Resolved

  • OPA356: Assist in providing junction-to-case thermal resistance data (Rjc) for various parts

    TI Thinks Resolved
    Part Number: OPA356 Hello Technocrats, Please provide junction-to-case thermal resistance data (Rjc) for the following parts, OPA356AIDBVR Thanks

  • OPA356 temperature sweep simulation

    Other Parts Discussed in Thread: OPA356 I want to implement a Pspice simulation with a temperature sweep and the Monte Carlo analysis for OPA356. From TI support I have got an answer the OPA356 spice model does not support such kind of simulation . I will very…

  • OPA356: Decoupling capacitor

    TI Thinks Resolved
    Part Number: OPA356 Hello all, The OPA356 datasheet says: "A 10µF ceramic bypass capacitor is the minimum recommended value; adding a 1µF or larger tantalum capacitor in parallel can be beneficial when driving a low-resistance load. Providing adequate…
    • Answered

  • OPA2810: Can I supply OPA2810 and OPA356 with asymmetric power rail?

    Resolved
    Part Number: OPA2810 Other Parts Discussed in Thread: OPA356 I have OPA2810 and OPA356. I'd like to configure OPA356 as I-V converter(Photodiode) and OPA2810 as second non invert or invert amplifier(integrator, G=10) AFAIK, some OP-AMPs supplied …
    • Resolved
    • Answered

  • OPA356: Current or voltage limiter for TIA to In-

    Resolved
    Part Number: OPA356 Other Parts Discussed in Thread: OPA355 , OPA627 I design a TIA with OPA356 and SFH250V(Photodiode): Since maximum photocurrent of SFH250V is 100uA, and I hope higher gain of photocurrent for my usage. Thus, 100k Rfb is necessary after…
    • Resolved

  • RE: OPA356: Amplification for Ultrasonic NDT Signal

    Hello Jon, Were you able to continue with the OPA356? It looks like another advantage with the OPA356 is that it is rail to rail, with the OPA858 you will face clamping at the negative supply of 1.05V with an input signal of 100mV and gain of 20. Thank…

  • OPA356-Q1: Cant generate PWM waveform for FET .

    Part Number: OPA356-Q1 Other Parts Discussed in Thread: OPA356 Hi guys, I want to generate a PWM signal the amplifer but somehow the output of the amplifer is not switching.Maybe you can suggest me a solution . It would be also be nice if you could also…

  • [FAQ] [H] Frequently Asked Questions - High Speed Amplifiers Selection Guide - CMOS Input Amplifiers

    Frequently Asked Questions: Amplifiers >> High Speed Amplifiers >> HSA Selection Guide >> CMOS Input Amplifier Selection Guide JFET Input Bipolar Input CMOS Input FDAS Power Amps VGAs TIAs Introduction: FET/CMOS…

  • OPA356: Active Shield Driver for High(ish) Speed Capacitive Load

    Part Number: OPA356 Other Parts Discussed in Thread: FDC2214 , , LM79 , LM7705 , FDC2214EVM , FDC1004 , OPA365 Hi, I’m trying to design an active shield driver for the FDC2214 that is able to accurately voltage follow the half-sine, 10MHz, 3.6V signal.…

Didn't find what you are looking for? Post a new question.