TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel

Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed the week of November 23.



Search tips
Showing 12,576 results View by: Thread Post Sort by
  • TPS63020: Temperature v/s efficiency curve across operating temp range and MTBF data

    Aidin Aidin
    Aidin Aidin
    TI Thinks Resolved
    Part Number: TPS63020 We are currently evaluating the following TI ICs for our application: TPS63020QDSJTQ1 As part of our reliability and performance assessment, we kindly request your support in providing: Temperature vs. efficiency curves…
    • 9 months ago
    • Simulation, hardware & system design tools
    • Simulation, hardware & system design tools forum
  • RE: OPA2333-HT: Performance of OPA2333-HT at temperature 210C

    Marek Lis
    Marek Lis
    You do NOT read the Fig 7 graph correctly since output swing cannot be +3V to -2.75V on +/-2.75V supplies - see below. Instead I would estimate typical output swing under 0.5mA load to be around 100mV from the rail at 125C (+2.65V on +2.75V supply)…
    • 8 months ago
    • Amplifiers
    • Amplifiers forum
  • RE: IWR6843ISK: Fall Detection Demo -> Radar Toolbox 1.30 and 3.20

    Santosh Krishnan
    Santosh Krishnan
    Hello. Please refer to the detection layer tuning guide for more information on these commands. I would look at modifying the range and angle threshold parameters(which are essentially SNR values that are used for determining whether a point is a valid…
    • over 1 year ago
    • Sensors
    • Sensors forum
  • RE: CC2745R10-Q1: Question About RSSI Availability in BLE Channel Sounding Mode 3

    Eshaan Tibrewala
    Eshaan Tibrewala
    Hello Mike, 1. Can RSSI be obtained directly from the Channel Sounding procedure (Mode 3)? No, Mode 3 is a combination of Phased based ranging tones and round trip time, so it gives a phase measurement (PCT) value and time of flight, but not RSSI…
    • 1 month ago
    • Bluetooth®︎
    • Bluetooth forum
  • MMWAVEPOEEVM: questions regarding MMWCAS-RF-EVM and MMWCAS-DSP-EVM

    Paniz Alsafi
    Paniz Alsafi
    TI Thinks Resolved
    Part Number: MMWAVEPOEEVM Hi TI's team, I have some questions regarding MMWCAS-RF-EVM and MMWCAS-DSP-EVM. I would appreciate it if you could help me with the following: 1. Real-time processing / UDP Is real-time processing supported for the MMWCAS…
    • 9 months ago
    • Sensors
    • Sensors forum
  • BOOSTXL-TUSS4440: BOOSTXL-TUSS4440

    Michael Wehrell
    Michael Wehrell
    TI Thinks Resolved
    Part Number: BOOSTXL-TUSS4440 Other Parts Discussed in Thread: BOOSTXL-TUSS4470 Tool/software: I have questions regarding the BOOSTXL-TUSS4470 I am designing an ultrasonic ranging system that does not rely on receiving an echo. It's…
    • over 1 year ago
    • Sensors
    • Sensors forum
  • LMX2694-EP: LMX2694 RF Output Buffer Pullup

    Chuck Howell
    Chuck Howell
    TI Thinks Resolved
    Part Number: LMX2694-EP I have a prototype circuit card using an LMX2694 to generate programmable RF signals in the 6 to 12 GHz range. The RF Output Buffer Pullup scheme is essentially copied from the Typical Application Schematic (Figure 8-9) in section…
    • 2 months ago
    • Clock & timing
    • Clock & timing forum
  • Answered
  • RE: AM6442: AM64x NOR QSPI TAP Mode at 50 MHz: Read Timing and Slew Rate Margin Issue

    Mathias Cuvelier
    Mathias Cuvelier
    Resolved
    Thanks for the clarification! Now I understand that the slew rate is a only reliability requirement here, not a timing constraint. I've found also this ticket which is close to our issue here: [FAQ] AM623: MMC0 HS200 slew rate - Processors forum - Processors…
    • 4 months ago
    • Processors
    • Processors forum
  • LMX2572LP: Phase Noise Limitations

    Evan McAuliffe
    Evan McAuliffe
    TI Thinks Resolved
    Part Number: LMX2572LP Other Parts Discussed in Thread: LMK61PD0A2 Hi there, We are using the LMX2572LP as our PLL frequency synthesizer in our transceiver design. To pass RF complaince testing with the largest margin possible we want to have the lowest…
    • 1 month ago
    • Clock & timing
    • Clock & timing forum
  • RE: THS4536: Can this device be used for attenuation (gain < 1)?

    Evan Kirkbride
    Evan Kirkbride
    Hi Shota, The THS4536 can be configured in a gain of G=0.1V/V. You can see some data for this condition in the datasheet that I took. The thing to look out for with these high input signals and the single-supply case is to make sure the input…
    • 7 months ago
    • Amplifiers
    • Amplifiers forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question