• SN74HCS125-Q1: SPI signal

  

  Peter Xu

  TI Thinks Resolved

  Part Number: SN74HCS125-Q1 Tool/software: Hi team, Can I use this device to buffer SPI signal(7.5MHz) in the system? I worry that there is some limit on this device. Regards, Peter

  • 1 month ago
  • Logic
  • Logic forum
Answered

• SN74HCS125-Q1: Use Satellite project

  

  ? ??

  Resolved

  Part Number: SN74HCS125-Q1 Other Parts Discussed in Thread: SN54AHC244-SP Tool/software: Hello experts, We want to use SN74HCS125-Q1 to the satellite project. Are there any restrictions on using it on satellites? Best regards, Toru Kimura.

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• SN74HCS125-Q1: The relationship curve between VT+ and VCC

  

  Jeff Yun

  Resolved

  Part Number: SN74HCS125-Q1 Hi, Team Hope you are doing well! From the datasheet of SN74HCS125-Q1, I can know the VT+max@2V/4.5V/6V. But what if I want to know the VT+max corresponding to other Vcc values? For example, when Vcc=3.3V(I think it…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN74HCS125-Q1: Max cable length this can drive.

  

  Derek Jackson

  Resolved

  Part Number: SN74HCS125-Q1 Other Parts Discussed in Thread: LMX2595 , SN74LVC125A-Q1 Outputs from the SN74HCS125-Q1 will be going off board through a 2m, 100-ohm cable. I cannot add anything on the receiving board which has a LMX2595 receiving the signals…

  • Resolved

  • over 3 years ago
  • Logic
  • Logic forum

• SN74HCS125-Q1: could you please help provide the Pspice model for SN74HCS125?

  

  Aki Li

  TI Thinks Resolved

  Part Number: SN74HCS125-Q1 Other Parts Discussed in Thread: SN74HCS125 , TINA-TI , SN74LVC1G17 Customer was asking for the PSpice model of SN74HCS125-Q1 for the simulation. Could you please help provide that? Thank you.

  • over 4 years ago
  • Logic
  • Logic forum

• SN74LVC3G17: Does TI has Pin-to-pin Q-grade or good Q-grade solution for SN74LVC3G17DCUR

  

  Abin Huang

  TI Thinks Resolved

  Part Number: SN74LVC3G17 Other Parts Discussed in Thread: SN74HCS125-Q1 Tool/software: Hi Team, my customer would like to find the Q grade solution for Q-grade. Could you provide the suggestion? Best, Abin

  • over 1 year ago
  • Logic
  • Logic forum

• SN74HCS244-Q1: buffer IC layout placement

  

  VIOLA LIAO

  TI Thinks Resolved

  Part Number: SN74HCS244-Q1 Other Parts Discussed in Thread: SN74HCS125-Q1 Tool/software: Hi, Currently we using buffer to prevent the SPI signal decade which might loss the package. But I'm not sure the buffer need to close to Tx or Rx. and…

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• TXB0108: Avoiding oscillations and ringing when buffering TXB0108 signals for off-board GPIO

  

  William Ridgeway

  Resolved

  Part Number: TXB0108 Other Parts Discussed in Thread: SN74HCS125-Q1 Hi, I’m working with a 3rd party device which contains a TXB0108 bidirectional voltage level translator. It is used, likely inappropriately, to drive GPIO signals to components external…

  • Resolved

  • over 4 years ago
  • Logic
  • Logic forum

• RE: SN74AUC17: SCHMITT-TRIGGER BUFFER

  

  Dylan Hubbard

  Hey Olin, All of the risks for not staying withing recommend operating conditions are noted under the Abs max table. All we have currently for this would be the SN74HCS125-Q1.

  • over 5 years ago
  • Logic
  • Logic forum
Answered

• SN74LVC1G17-Q1

  

  Ali Khan

  Resolved

  Other Parts Discussed in Thread: SN74HCS125-Q1 , SN74HCS126-Q1 I want to design a hardware debounce circuit and I need help with some calculations. 1: How I can figure out the bounce time required for a switch prior to physical testing? 2: I noticed that…

  • Resolved

  • over 4 years ago
  • Switches & multiplexers
  • Switches & multiplexers forum

Didn't find what you are looking for? Post a new question.