Search tips
Showing 57 results View by: Thread Post Sort by

  • THS3095: Noise Optimization

    Part Number: THS3095 Other Parts Discussed in Thread: LMH6702 , LMH6609 Tool/software: The THS3095 is advertised as a low noise amplifier with 1.1nV/sqHz voltage and 14pA/sqHz current noise. The problem is that the datasheet recommends using a feedback…

  • THS3095: offset voltage drift and bias current drift MAX

    TI Thinks Resolved
    Part Number: THS3095 Hi team, Only typical values for the average offset voltage drift and bias current drift are listed. Could you please provide the data for the maximum values as well? Best Regards, Shota

  • THS3095: Maximum allowed voltage between the Exposed pad and the amplifier power supply pins.

    Part Number: THS3095 Tool/software: Hi, we use THS3095 opamps, which are supposed to have an electrically not connected exposed pad, as FET drivers. The supply voltage is 50V + 12V and 50V - 5V. So the amplfier supply is set around +50V. Currently…

  • THS3095: OP-Amp not working with dual supply votlage

    Part Number: THS3095 Other Parts Discussed in Thread: TPS65131 , Tool/software: Hi, I intend to amplify a signal using THS3095DDA. I am using the same circuit as the evaluation board of THS3095 ( THS3095EVM Evaluation board | TI.com ): except without…
    • Answered

  • THS3095: The frequency response and the recommended RISO value when the load capacitance is 1200pF

    Resolved
    Part Number: THS3095 Tool/software: Dear Specialists, My customer would like to know Riso value at load capacitance 1200pF. I would be grateful if you could advise. --- Figure 7-7 on page 11 shows Capacitive Load Frequency Response, and Figure…
    • Resolved
    • Answered

  • THS3095: 1PPS [0-10V] 50 ohms Driver

    Resolved
    Part Number: THS3095 Other Parts Discussed in Thread: THS3491 , UCC27537 , TINA-TI Hello, I need to design a 1PPS driver with rising edges <50ns and driving a 10V voltage through a 50ohms adapter (the total supply is therefore 20V due to the bridge…
    • Resolved
    • Answered

  • THS3095: THS3095 Asymmetric Supply

    Resolved
    Part Number: THS3095 Other Parts Discussed in Thread: THS3491 Hi, Is it possible to supply the THS3095 with for example +20V/-5V asymmetrically? Thanks, Andras
    • Resolved

  • THS3095: Negative Dual-Supply Operation

    TI Thinks Resolved
    Part Number: THS3095 Hi Team, Our customer has an application wherein they need to drive -27V output from THS3095. Is it possible to set +Vs to 0V and -Vs to -30V? If this would be possible what particular limitations should we consider? Thanks in advance…
    • Answered

  • TIDA-01486: Available gain for the THS3095

    Resolved
    Part Number: TIDA-01486 Other Parts Discussed in Thread: THS3095 , Hi, I've read in the TIDA-01486 that you have adjusted the gain of the op amp on the board. You changed them from 10 to 2. You have adviced to look at recommended resistor values in…
    • Resolved

  • THS3095: Use in a PI-regulator to drive a Mosfet for current regulation

    Part Number: THS3095 Other Parts Discussed in Thread: LM7171 , , THS3491 Hi, I am working on a PI regulation design, where I currently use the LM7171 OpAMP to regulate the gate of a Mosfet to control the current through the Mosfet, with a supply of…

Didn't find what you are looking for? Post a new question.