Search tips
Showing 20 results View by: Thread Post Sort by

  • TLV27L1: Wild current consumption spread at Lower Vdd

    TI Thinks Resolved
    Part Number: TLV27L1 Other Parts Discussed in Thread: TLV271 , TLV07 Tool/software: Dear all, I have a circuit much like what it is on this page - https://e2e.ti.com/support/amplifiers-group/amplifiers/f/amplifiers-forum/806016/tlv27l1-unstable-performance…
    • Answered

  • TLV27L1: TLV27L1

    Resolved
    Part Number: TLV27L1 Hi guys, three months ago our company bought about 9000 pieces of TLV27L1IDBVR, but it seems that the devices inside the reel are not the TLV27L1. The devices shown an input bias current of 70/80 nA (nano-amps) instead of 1 pA typ…
    • Resolved

  • TLV27L1: Looking for a lower power alternative than TLV9101

    Answer Suggested
    Part Number: TLV27L1 Other Parts Discussed in Thread: TLV9101 , OPA244 , OPA251 , TLV6003 , TLV2401 Hey Op Amp team, I have a customer considering migrating from TLV27L1 to a newer op amp alternative and we noticed that the landing page recommends the…
    • Answered

  • TLV27L1: input pins abs max rating versus input common mode voltage.

    Resolved
    Part Number: TLV27L1 Hi, TLV27L1 datasheet states: Abs. max rating of input voltage is Vs (Note 1 says "relative to GND pin"). is this referring to the max positive voltage allowed on the input pin? What is the abs. max rating for the negative voltage…
    • Resolved
    • Answered

  • TLV27L1: Unstable performance

    Resolved
    Part Number: TLV27L1 Dear Sir/Madam, I am using TLV27L1IDBVR. The circuit is unstable, after I removed C7, and it becomes stable. Can you explain why? I am using compliance voltage at input. I have a constant current source 23mA as supply. The compliance…
    • Resolved

  • TLV27L1: Biphasic Signal Generation Problem

    TI Thinks Resolved
    Part Number: TLV27L1 Hello, I have asked my question before in this form. Now I face the problem again. I feed square waves of the Opamp for both inputs and get biphasic signal. But I don't what it is happening then I lost negative cycle of my signal…

  • RE: TLV27L1: can TLV27L1 operate with full functionality with CMV = -0.2V for temperature range -20deg.C to +85deg.C

    Nitish, I have to take back the phase reversal claim as the input current from the negative input voltage caused my power supplies to dropout giving the illusion of output phase reversal. Almost all of the input current is collected by the VS+ pin…
    • Answered

  • TLV27L1: Biphasic Signal Generation Problem

    Resolved
    Part Number: TLV27L1 Other Parts Discussed in Thread: TLV2371 Hello, I use TLV27L1 OpAmp in my circuit. I feed inverting and non inverting inputs with square waves. But as an output, I did not get biphasic signal. Output of the opamp is just an monophasic…
    • Resolved

  • RE: TLV27L1: Supply current of TLV27L1 with Vdd = 12V versus load resistance when opamp output is between 2V to 4V.

    Hi Nitish, Thank you for your interest in the TLV27L1. Please allow me 48 hrs hours while I investigate this issue. Thank you for your patience! Regards, -Mamadou General Purpose Amplififer

  • TLV27L1: TLV27L1IDBVR

    TI Thinks Resolved
    Part Number: TLV27L1 TLV27L1IDBVR and TLV27L1IDBVRG4 the differen

Didn't find what you are looking for? Post a new question.