Frequent Questions

  • [FAQ] Auto Protocol Selection Guide

    This serves as a selection guide for our automotive-grade devices and outlines the typical protocols associated with these devices. 1:1 2:1 3:1 4:1 8:1 SN74LVC1G66-Q1 SN74LVC2G66-Q1 TMUX7212…

  • [FAQ] TDA4VEN-Q1: C7x reset from CCS issues double page Fault

    Part Number: TDA4VEN-Q1 Trying to reset c7x through CCS issues a double page fault.

  • [FAQ] AM625: OSPI Access Across Different Cores

    Part Number: AM625 Other Parts Discussed in Thread: AM62P , AM62L On different TI SITARA MPU SoCs, lets have a look at SoC wise cores which have access to the OSPI module/Controller in the current MCU+ SDK Software offering. Please refer the table below…

  • [FAQ] AM625: How to configure Timer in Interrupt mode

    Part Number: AM625 Other Parts Discussed in Thread: SYSCONFIG Lets have a look at the implementation of application using a TIMER module(DM TIMER) in Interupt mode of operation. The application code can be used as it is or as a baseline for configuring…

  • [FAQ] AM62D-Q1 Custom board hardware design – AUDIO-AM62D-EVM Audio Functionality Implementation Related Queries and Design Notes

    Part Number: AM62D-Q1 Other Parts Discussed in Thread: AUDIO-AM62D-EVM Hi TI experts, I am planning to reuse the AM62D-Q1 AUDIO-AM62D-EVM schematics for my custom board design. I see the below schematic sections (pages) added to the AUDIO-AM62D-EVM…

  • [FAQ] AM6421: RESETSTATz output during ROM boot

    Part Number: AM6421 Hello, During a successful QSPI boot, I have captured the following signals: MCU_PORz, RESETSTATz, OSPI_CLK, OSPI_CS. I'm observing that roughly 35mS after RESETSTATz goe high it has a 160uS period where it drops low. Looking at…

  • [FAQ] TDA4VH-Q1: How to configure the SerDes lane for PCIe, USB, Ethernet, and Display in Linux?

    Part Number: TDA4VH-Q1 Other Parts Discussed in Thread: TDA4VH The high speed interfaces on the TDA4x share the SerDes lanes. The lanes can be muxed for different interfaces, but how can I configure them within Linux?

  • [FAQ] AM2754-Q1: Working Configurations for 8S-8S-8S on S28HS512T Serial NOR OSPI Flash

    Part Number: AM2754-Q1 Other Parts Discussed in Thread: SYSCONFIG In MCU+ SDK 11.02, the OSPI and Flash examples are configured by default to operate at the highest protocol: 8D-8D-8D. For configuring 8S-8S-8S SDR Protocol on S28HS512T Serial NOR OSPI…

  • [FAQ] TDA4VH-Q1,TDA4VE,TDAVAL,TDA4VL,TDA4VP-Q1,TDA4AP-Q1: How to reset C7x and load binary faster via CCS

    Part Number: TDA4VH-Q1 Hi, After reset of C7x, i am trying to load newer C7x binary, but the second load takes a lot of time. Could you please help me to solve this issue.

  • [FAQ] AM263P4-Q1: Last 24 bytes of Bank0, Bank1 in OCRAM are no longer visible

    Part Number: AM263P4-Q1 Hi, Regarding the E2E mentioned below, could you please provide us with further information? We are currently using SDK 9.2, and due to our development schedule, we do not have sufficient time to migrate to SDK 11.0. Could you…

View FAQ threads
Recommended For You