Frequent Questions

  • [FAQ] AM263P4: Enabling GPIO interrupt in MCAL for AM263P4

    Part Number: AM263P4 Tool/software: In this FAQ i will show you the configurations required to enable the interrupts for p ins MCU_GPIO64 and MCU_GPIO63 in MCAL for AM263P4.

  • [FAQ] How to avoid crashing the DM R5F when writing custom DM R5F firmware

    Parts Discussed in Thread: AM62x, AM62Ax, AM62Dx, AM62Px The primary role of the Device Management (DM) R5F core is to run the DM task. However, on some devices (not all devices!), TI supports writing custom code to run on the DM R5F, alongside the…

  • [FAQ] SBL boot: How to find the DM R5F firmware that is loaded by SBL

    Parts Discussed in Thread: AM62x, AM62Ax, AM62Dx, AM62Px The primary role of the Device Management (DM) R5F core is to run the DM task. However, there may be other non-DM code running on the DM R5F, alongside the DM task. The firmware running on the…

  • [FAQ] BQ25611D: What is the function of the /QON pin on BQ2561x?

    Part Number: BQ25611D Other Parts Discussed in Thread: BQ25619 , BQ25618 , Tool/software: The /QON pin has multiple functions on the BQ25611D, BQ25618/E, and BQ25619/E and is pulled up internally. The only thing connected to this pin should be some switch…

  • [FAQ] BQ25611D: Why do I have to read the fault status twice to see the cleared fault on BQ2561x?

    Part Number: BQ25611D Other Parts Discussed in Thread: BQ25619 , BQ25618 , Tool/software: When a fault occurs on BQ2561x an /INT pulse is sent to the host. For the BQ25611D, BQ25618/E, and BQ25619/E the fault status in REG0x09[7:0]/REG0x0A[6:4] are…

  • [FAQ] BQ25611D: What is ship mode and how do I enter and exit it in BQ2561x?

    Part Number: BQ25611D Other Parts Discussed in Thread: BQ25619 , BQ25618 , Tool/software: The BQ2561x has a mode to minimize quiescent current for the BQ25611D, BQ25618/E, and BQ25619/E from the battery in cases when the system load is not needed to be…

  • [FAQ] BQ25611D: How do I set the temperature range I desire using the TS pin on BQ2561x?

    Part Number: BQ25611D Tool/software: The BQ2561x TS pin is used to monitor the battery temperature via a thermistor with a pull-up and pull-down resistor. As the two resistors represent two unknowns when designing the TS circuit, only two temperature…

  • [FAQ] TDA4AL-Q1: Large byte transfer

    Part Number: TDA4AL-Q1 Tool/software: Example application on SDK 10.0 to show large byte transfer between CDD IPC(MCU1_0) and Linux (A72) using cdd_ipc_rc_linux ,rpsmg_char_simple applications on J721S2 ?

  • [FAQ] How to check if Linux can communicate with a non-Linux core through RPMsg

    Other Parts Discussed in Thread: AM67 , AM67A Before Linux can communicate with a non-Linux core over the RPMsg inter-processor communication (IPC) protocol, several things needs to be true: 1) RPMsg between Linux and the non-Linux core must be supported…

  • [FAQ] Linux: How to check what binary is running on the DM R5F

    Other Parts Discussed in Thread: AM67 , AM67A Parts Discussed in Thread: AM62x, AM62Ax, AM62Dx, AM62Px, AM67, AM67A The primary role of the Device Management (DM) R5F core is to run the DM task. However, there may be other non-DM code running on the…

View FAQ threads
Recommended For You