Frequent Questions

  • [FAQ] How to calibrate the HW based protections on the BQ27Z746 and BQ27Z758?

    Part Number: BQ27Z758 Other Parts Discussed in Thread: BQ27Z746 , , BQSTUDIO Tool/software: The BQ27Z746 and BQ27Z758 share the same process for calibrating the hardware (HW) based protections. There are some things that are important to note…

  • [FAQ] MSP Homepage

    Welcome to the MSP E2E Homepage! Here you will find a variety of resources supporting the MSPM0 microcontroller family Click on a topic below to find a collection of relevant documents and FAQs. If this is your first time using MSPM0, take a look…

  • [FAQ] AM263P4: How to perform flash verification in AM263P.

    Part Number: AM263P4 Other Parts Discussed in Thread: UNIFLASH Tool/software: It is not only enough to flash images but to verify them is also necessary. Verification allows the user to know if flashing has been done properly. There are two methods…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM64x / AM243x / AM62Ax / AM62Px / AM62D-Q1 / AM62L - Supported bootmode configurations

    Part Number: AM62L Other Parts Discussed in Thread: AM62D-Q1 , AM625 , AM623 , AM620-Q1 , TMDS64EVM Tool/software: Hi TI experts help me understand the supported bootmode configurations for the below family of processors AM625 / AM623 / AM620…

  • [FAQ] AM62L ( AM62L32 , AM62L31 ) Design Recommendations / Custom board hardware design – Queries regarding power architecture including PMIC

    Part Number: AM62L Other Parts Discussed in Thread: TPS65214 , AM62P-Q1 Tool/software: Hi TI Experts, I am designing custom board using AM62L. Can you provide your inputs on the supported power architecture when custom board design is configured…

  • [FAQ] What are some new & exciting parts that TI offers?

    Other Parts Discussed in Thread: TLV320ADC5120 , TLV320ADC6120 , PCM1863 , PCM1862 , PCM1804 , PCM1822 , PCM1820 , PCM6020-Q1 , PCM1808-Q1 , PCM3120-Q1 , PCM1863-Q1 , PCM1862-Q1 , PCM5100A , PCM1754 , PCM5102A , PCM5101A , PCM1789 , PCM1754-Q1 , PCM5100A…

  • [FAQ] AM62P: How to Fix Missing TIFSSTUB to enable Low Power Modes in Linux SDK 10.0/10.1?

    Part Number: AM62P Tool/software: I've successfully tested low power modes on AM62P using the default images. But I've tried to build my own U-Boot images, but now low power modes are not working. What is the cause and solution to this?

  • [FAQ] AM62L ( AM62L32 , AM62L31 ) Why is MMC1 powered by two different voltage supplies, VDDSHV1 and VDDSHV3 ?

    Part Number: AM62L Tool/software: Hi TI Experts, Could you confirm that the voltage domains are correct for the MMC1_SDCD and MMC1_SDWP pins? The datasheet shows both MMC0 and MMC2 as having all member pins bellowing to the same voltage domain.…

  • [FAQ] TDA4VM: How to address the gPTP Sync failure post reset recovery of CPSW in Ethenret Firmware?

    Part Number: TDA4VM Tool/software: After a CPSW reset recovery from ETHFW, gPTP fails to re-establish synchronization, impacting time-sensitive applications.

  • [FAQ] SK-AM64B: Building and Booting an UBIFS-based Linux rootfs from OSPI NOR Flash using TI Processor SDK Linux v11.x Yocto Sources

    Part Number: SK-AM64B Other Parts Discussed in Thread: SK-AM62B Tool/software: Overview The TI SK-AM64B EVM has an on-board 64MB-sized OSPI Flash chip that can be used to boot the AM64x device from. The documentation associated with SDK v11.0 contains…

View FAQ threads
Recommended For You