• State Resolved
  • Locked Locked
  • Replies 7 replies
  • Answers 1 answer
  • Subscribers 32 subscribers
  • Views 466 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

SN65HVD01: SN65HVD01 RS485 Chassis GND vs Signal GND request for help with the design (PCB Lay out)

won seungyeon
Prodigy 70 points
Part Number: SN65HVD01

HI. 

I designed using SN65HVD01 parts in my design.

In my design I have Chassis ground and signal ground.

I separated the pcb layout using a capacitor and a resistor.

At this point, want to place the capacitor in each Mounting (machine) hole.

Is it a good Isolation?
(Note, it is not possible to galvanic Isolation.)

Any other recommendations?

I will wait for your reply.

Thank you

Best Regards

  • +1
    TI__Mastermind 45397 points

    Hi Won,

    Generally for our boards that we design we just separate the chassis ground (which we typically call Earth in our schematics) with a capacitance and resistance in parallel.

    Is this board a 2 layer board? If so I think it looks okay but if you have any higher speed circuitry that runs on the other layer of the board over the gap you have shown in the picture attached it could change the impedance of the line - it probably wouldn't be a huge concern however it is something to consider especially at higher data rates/longer transmission lines  - if you have four layers or more I always will suggest separating the ground planes to different layers of the board  with a typical arrangement of  Top Layer: Main circuit, layer 2: signal ground, layer 3: VCC, and layer 4: bottom layer (if needed for traces) + Earth. I understand it may not be possible to do more layers and if not I think what you have proposed is okay.

    Please let me know if you have any other questions!

    Best,

    Parker Dodson 

  • 0 in reply to Parker Dodson
    Prodigy 70 points

    this is board a 2 layer board.

    if 2 layer board are you saying that it is okay to separate the ground with multiple capacitors ( Each Mounting hole has capacitors)?

    Thank you.

    Parker Dodson

  • +1 in reply to won seungyeon
    TI__Mastermind 45397 points

    Hi Won,

    Yes - that is correct - capacitive isolation between the planes is okay for this layout since it is layers like you mentioned. A resistor could be added in parallel to help reduce ground loop current but that is optional.

    Please let me know if you have any other questions!

    Best,

    Parker Dodson

  • 0 in reply to Parker Dodson
    Prodigy 70 points

    Thank you for your prompt reply. 

    Regards

    seungyeon

  • 0 in reply to won seungyeon
    TI__Mastermind 45397 points

    Hi Won,

    No problem!  If you have any other questions please let me know!

    Best,

    Parker Dodson

  • 0 in reply to Parker Dodson
    Prodigy 70 points

    Hi Paker Dodson.

    Thank you for replying well.

    I have additional question

    " resistor could be added in parallel to help reduce ground loop current" you said

    Can you recommend a resistor value?

    I think 0 ohms or 100 ohms are fine, but what do you think?

    Thank you.

  • 0 in reply to won seungyeon
    TI__Mastermind 45397 points

    Hi Won,

    Typically we see a 100 Ohm resistor between Chassis/Signal grounds when they are used. So I think 100 should be fine.

    If you have any other questions please let me know!

    Best,

    Parker Dodson