Part Number: TMS570LC4357

Explain the detailed process to enable 256 BUFFERS/EXTENDED_BUF_ENA Feature OF MibSPI.

Part Number: MSPM0-SDK

Important note for early MSPM0 customers

TI recently launched a new family of Arm Cortex-M0+ MCUs, including the MSPM0L series and MSPM0G series. These MCUs are accompanied by a comprehensive amount of collateral and tools support which might not be compatible for early adopters.

This guide is intended to clarify which documentation and tools should be used for early samples and production samples.

Update: The repository for MSPM0 early samples on My Secure Resources has been deprecated. It's recommended to use production samples moving forward and all documentation and tools will continue being released on TI.com and dev.ti.com. Please contact your local sales if you need access to early samples content.

How to determine MSPM0 Sample versions

You have production samples if:

• You were able to order samples directly from ti.com and didn’t need to contact a TI sales office.
• Your device is marked as MSPM0Lxxx/MSPM0Gxxx/M0Lxxx/M0Gxxx/Lxxx/Gxxx (depending on package)
• Your LaunchPad is marked as Rev A
• The VERSION bit fields (31-28) in the DEVICEID Register (see Technical Reference Manual) is 0x1
• Note that MSPM0L production devices are sampling now; however, MSPM0G devices are not available yet in production silicon.

You have early samples if:

• You did not order samples directly from ti.com and to order samples through a TI sales office.
• Your device is marked as XM0L/XM0G
• Your LaunchPad is marked as Rev 1.0
• The VERSION bit fields (31-28) in the DEVICEID Register (see Technical Reference Manual) is 0x0

Documentation

Software and Tools

Part Number: AM2434

Hi,

I'm looking at enabling in the field provisioning (also factory provisioning) of devices that are using the AM243x/AM64x family of Sitara products. I would like to be able to uniquely identify each module and was hoping the SoC had a register containing a unique identity (such as lot code / line build information, or potentially a unique serial number). 

I would use this to be able to generate targeted firmware or provision only individual devices in the field. 

Is there anything like this available in the register map that could be used and would not change, it also needs to be guaranteed unique across all units.

Thanks,

Sasha 

Part Number: LP-AM243

Hi experts,

I am evaluating AM243x with MCU+SDK 8.5.0.24.

I noticed in the FreeRTOS docs that FreeRTOS has a multiprocessing feature called SMP, which would be an interesting option for AM243x.

Is this feature included in the TI FreeRTOS port? Is there an example how to set it up (i. e. what to start on which core)?

Best regards

Alexander

Part Number: AM2634

Q1. How to debug TIFS-MCU on Cortex M4 in HS-FS devices ?

Q2. How to debug TIFS-MCU on Cortex M4 in HS-SE devices ?

Q3. In HS-SE devices, is there a way to leverage the flow to open the debug for HSM M4 in development environment ?

Part Number: MCU-PLUS-SDK-AM263X

Hi Experts,

How do I configure CPSW 2G ALE to filter packets based on VLAN, Ethernet Type, Source MAC, Destination MAC, IP address etc?

Part Number: MCU-PLUS-SDK-AM263X

Hi

How to Configure GPIO Interrupts in AM263x for individual GPIO pins.

How is it different from the existing GPIO Bank Interrupt Configuration example in the SDK.

The following FAQ applies to AM243x LaunchPad (LP-AM243), AM263x LaunchPad (LP-AM263), AM243x General Purpose Evaluation Module (TMDS243GPEVM, TMDS243EVM), AM263x Control Card (TMDSCNCD263). 

1. Do the Sitara MCU evaluation modules (EVM) and LaunchPads (LP) have any power requirements?

2. What is the EVM/LP Power-on sequence after a type-C connection is established?

3. What should be done if the Power-good status LEDs are not glowing following the type-C connection? 

4. How does the EVM/LP handle a type-C connection to supply power to the board?

5. How does the TUSB320 Port Controller determine the current mode?

6. Can I use a USB type-A to USB type-C cable to supply power to the board?

7. Are all USB type-C to USB type-C connections capable of high current?

8. Are all USB type-C cables rated for 5V/3A?

9. Can I use a >15W universal wall adapter that uses a DC barrel jack with a DC barrel jack to USB type-C adapter? 

10. What is the recommended solution for powering Sitara MCU evaluation modules and LaunchPads?

Part Number: MCU-PLUS-SDK-AM243X

How to identify which image should I use ? Should I use *.hs_fs.tiimage or *.tiimage for SBL programing on my device.

Does it matter ? Does it affect any of my application ?

Part Number: MCU-PLUS-SDK-AM263X

[AM263-SBL] Where can I find information of getting started with the AM263 SBL, Bootflow and Booting Tools?